MI SR20 Swap, HKS 3037s Turbo, Full-Race, Tial, Exedy, ID 1000's, SARD Rail - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

240 GTR · 02-26-2013, 08:16 AM

Selling the redtop sr20 setup from my pro-am car. I bought it from JDM-online.com back in 06 or 07. It was used for multiple events up until the end of 2010. It's been a really solid motor...never had any issues with it. I used to run it with an s15 t28 on 16 psi, power fc, sti injectors, and z32 maf. Oil was changed religiously after every event with 10w-40 Rotella T, filters changed every other event. I've had really good luck with this motor, but it's time to move on. Hopefully somebody else can put it to good use.

What you're getting:
-Redtop s13 SR20 Longblock
-s13 SR trans with B&M shifter (no grinds or blown gears. shifts really well, had MT-90 in it.)
-Exedy Stage 2 Clutch (about 14 events on it. still grabs hard)
-Exedy lightweight flywheel
-Engine harness, trans harness, and ignitor (setup to go into SOHC ka s13. has also been modified for a power fc d-jetro, but all maf wiring is still in tact. ignitor gets relocated inside of the car).
-New starter
-Koyo Radiator with Altima dual electric fans and auto fan controller
-Nismo 65C thermostat
-6AN PS Lines, cooler, reservoir

What it needs:
-Turbo, manifold, lines (I have a good t25, gt28rs, hy35, stock manifolds, and lines available for extra.)
-ECU
-MAF
-Injectors
-Alternator needs rebuild soon
-IC and intake setup
-Front and rear main seals leak a little

Price: $2000
Location: Near Ann Arbor, MI

Available Separately:

Turbo setup shown above: $1700
-Made 370 whp @15 psi on my stock internal SR
-HKS 3037s (no blown seals, normal shaft play for BB turbo, no bent fins, aluminum elbow welded onto comp. outlet)
-Full Race bottom mount manifold
-Tial 40mm v-band wastegate with dump tube
-4 bolt turbo elbow/downpipe
-SS braided oil and water lines

Injector Dynamics 1000cc w/ Sard Rail: $500
-Installed, but never ran. These are basically brand new.
-Intake manifold not included
-Fuel rail has 8AN inlet and outlet fittings

Mid-mount Intercooler setup: $500
-Spearco core
-Custom aluminum piping (made specifically for the turbo setup above, but should work with others with small modification to hot pipe)
-Tial 50mm BOV on cold side

Take the engine, HKS turbo setup, injectors, and IC setup for $4300

sil15yaz · 02-26-2013, 05:13 PM

send email to me. [email protected]. interested in your id injectors and sard fuel rail

240 GTR · 03-11-2013, 09:37 AM

bump it uppp

Turbo Nismo · 03-13-2013, 12:12 PM

Are you willing to sold separately the Tial 40mm v-band wastegate? If yes, pm how much you want for it shipped to Puerto Rico, 00745?

RocketBUNNY · 03-13-2013, 12:33 PM

Part out just full race bottom mount mani? How much if so?

Rb26kouki · 03-13-2013, 12:36 PM

Does the manifold have a hole in it?
Also how many miles on the 3037S

240 GTR · 03-14-2013, 10:04 AM

Quote:

Originally Posted by Rb26kouki

Does the manifold have a hole in it?
Also how many miles on the 3037S

In the above picture, the tube off the manifold for the wastegate had broken off. It has since been rewelded in it's original position. I drove the car afterwards with no issues.

The 3037s came on a car that I bought that was built in '06. It was driven on track 2 times, then parked until I bought it in '10. I used the turbo for about 10 events since I've owned it.

Everyone else has been pm'd!

nOaAAa · 03-13-2013, 12:46 PM

pm'd you... send me your contact info

Wegs · 03-13-2013, 06:31 PM

http://zilvia.net/f/sale-items/506030-vh45-swap.html

trade?

02-26-2013, 08:16 AM	#1
240 GTR Zilvia Junkie Join Date: Mar 2006 Location: michigan Posts: 316 Trader Rating: (10) Feedback Score: 10 reviews	SR20 Swap, HKS 3037s Turbo, Full-Race, Tial, Exedy, ID 1000's, SARD Rail Selling the redtop sr20 setup from my pro-am car. I bought it from JDM-online.com back in 06 or 07. It was used for multiple events up until the end of 2010. It's been a really solid motor...never had any issues with it. I used to run it with an s15 t28 on 16 psi, power fc, sti injectors, and z32 maf. Oil was changed religiously after every event with 10w-40 Rotella T, filters changed every other event. I've had really good luck with this motor, but it's time to move on. Hopefully somebody else can put it to good use. What you're getting: -Redtop s13 SR20 Longblock -s13 SR trans with B&M shifter (no grinds or blown gears. shifts really well, had MT-90 in it.) -Exedy Stage 2 Clutch (about 14 events on it. still grabs hard) -Exedy lightweight flywheel -Engine harness, trans harness, and ignitor (setup to go into SOHC ka s13. has also been modified for a power fc d-jetro, but all maf wiring is still in tact. ignitor gets relocated inside of the car). -New starter -Koyo Radiator with Altima dual electric fans and auto fan controller -Nismo 65C thermostat -6AN PS Lines, cooler, reservoir What it needs: -Turbo, manifold, lines (I have a good t25, gt28rs, hy35, stock manifolds, and lines available for extra.) -ECU -MAF -Injectors -Alternator needs rebuild soon -IC and intake setup -Front and rear main seals leak a little Price: $2000 Location: Near Ann Arbor, MI Available Separately: Turbo setup shown above: $1700 -Made 370 whp @15 psi on my stock internal SR -HKS 3037s (no blown seals, normal shaft play for BB turbo, no bent fins, aluminum elbow welded onto comp. outlet) -Full Race bottom mount manifold -Tial 40mm v-band wastegate with dump tube -4 bolt turbo elbow/downpipe -SS braided oil and water lines Injector Dynamics 1000cc w/ Sard Rail: $500 -Installed, but never ran. These are basically brand new. -Intake manifold not included -Fuel rail has 8AN inlet and outlet fittings Mid-mount Intercooler setup: $500 -Spearco core -Custom aluminum piping (made specifically for the turbo setup above, but should work with others with small modification to hot pipe) -Tial 50mm BOV on cold side Take the engine, HKS turbo setup, injectors, and IC setup for $4300 __________________ Detroit Drifting Co.- Detroit, MI

03-11-2013, 09:37 AM	#3
240 GTR Zilvia Junkie Join Date: Mar 2006 Location: michigan Posts: 316 Trader Rating: (10) Feedback Score: 10 reviews	bump it uppp __________________ Detroit Drifting Co.- Detroit, MI

03-13-2013, 12:12 PM	#4
Turbo Nismo Zilvia Addict Join Date: Oct 2009 Location: Puerto Rico Posts: 731 Trader Rating: (18) Feedback Score: 18 reviews	Are you willing to sold separately the Tial 40mm v-band wastegate? If yes, pm how much you want for it shipped to Puerto Rico, 00745? __________________ IG: chris___s14

02-26-2013, 05:13 PM	#2
sil15yaz Leaky Injector Join Date: Feb 2013 Location: brunei darussalam Posts: 146 Trader Rating: (1) Feedback Score: 1 reviews	send email to me. [email protected]. interested in your id injectors and sard fuel rail

03-13-2013, 12:33 PM	#5
RocketBUNNY Zilvia Junkie Join Date: Feb 2013 Location: Red Deer, AB Canada Age: 39 Posts: 321 Trader Rating: (11) Feedback Score: 11 reviews	Part out just full race bottom mount mani? How much if so?

03-13-2013, 12:36 PM	#6
Rb26kouki Zilvia FREAK! Join Date: Apr 2012 Location: Commerce Age: 32 Posts: 1,474 Trader Rating: (62) Feedback Score: 62 reviews	Does the manifold have a hole in it? Also how many miles on the 3037S

03-13-2013, 12:46 PM	#8
nOaAAa Zilvia Junkie Join Date: Jan 2007 Location: SoCal Age: 39 Posts: 495 Trader Rating: (3) Feedback Score: 3 reviews	pm'd you... send me your contact info

03-13-2013, 06:31 PM	#9
Wegs Leaky Injector Join Date: Oct 2011 Location: Long Island Posts: 84 Trader Rating: (0) Feedback Score: 0 reviews	http://zilvia.net/f/sale-items/506030-vh45-swap.html trade?