MD FS: SR, Hood, Gaskets, OEM - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

BoostinIX · 05-18-2011, 08:35 PM

Stuff's taking up room, make offers.

All parts located at 20723. Will meet within reason. For paypal add 3%/Send as gift. As is/sales final. Feel free to PM questions, SR parts came off a Zerolift clean unmodified motorset, but have never personally used them.

-S14 SR20 WaterPump

20 P.U. / 25 Shipped

Bought a new water pump before disassembling the motor, and the old water pump looks brand-new inside. Might as well use the new one, so this one can go. Could essentially eat off it. Blades look great.

-Chaser CF Kouki Hood - Cheap!

Asking 200 (P.U. ONLY)

This HAS to go. Seriously. Make me an offer. Got 2 hoods too many in the garage. Needs to leave soon. Perfect chance for a cheap Kouki conversion.

The good:
Great at heat management. After carwash, can see it fog up the window with the raised rear section. Helped keep my engine nice and cool at the beginner's clinic. (factory cooling system, never went above 180)

Already drilled for AeroCatch latches. If you've had this done, you know this is a PITA/couple hours to get them perfect at a shop. Already drilled, ready to mount up new latches and go.

AeroCatch's not included.

The bad:
Has the standard clearcoat cracks from trying to use the stock hood latch, as well as more clear cracks on the drivers headlight area from a deer impact. Was low speed, deer more "bounced". Didn't hurt the hood, just the clearcoat.

-Stock SR manifold off my S14 SR.

50 P.U. / 60 Shipped

-OEM Accordian

20 P.U. / 25 Shipped

Got a Greddy, no longer need. I couldn't find any rips or tears.

-OEM Heat shields

10 P.U. / 15 Shipped

Wrapped Tomei mani and Coated turbo, no longer need.

-OEM SR fly off my S14 SR

-50 P.U. / 65 Shipped (Heavy....)

Upgrading to lightweight, won't need.

-OEM S14 Metal turbo gasket

10 P.U. / 15 shipped

-10 OEM S14 SR20 Head Bolts (No washers)

-10 P.U. / 15 Shipped.

Yes, they're used. Yes, the FSM gives you the measurements for checking if you can reuse them, no I didn't measure them (don't have anything exact enough). I got a new set for cheap, so these can go.

-BNIB OEM S14 SR20 Head Gasket

25 P.U. / 35 shipped

Got this with my kit, but since gotten a MHG. Never installed.

-BNIB OEM S14 SR20 Exhaust Manifold Gasket

15 P.U. / 25 shipped

Came with kit, my Expreme manifold came with the 7 layer so no longer needed. Never installed.

BoostinIX · 05-19-2011, 11:16 AM

Bumpage!!!

Will accept most reasonable offers. Need things gone.

BoostinIX · 05-20-2011, 07:00 AM

Bump 2, come ooooooooon schwartz

Firebat060 · 05-22-2011, 03:51 AM

Pm sent. Interested in heat shields.

yongai27 · 05-22-2011, 09:55 PM

Do u have aerocatch pins for sale?

05-18-2011, 08:35 PM	#1
BoostinIX Zilvia Addict Join Date: Feb 2008 Location: Laurel, MD Age: 39 Posts: 815 Trader Rating: (29) Feedback Score: 29 reviews	FS: SR, Hood, Gaskets, OEM Stuff's taking up room, make offers. All parts located at 20723. Will meet within reason. For paypal add 3%/Send as gift. As is/sales final. Feel free to PM questions, SR parts came off a Zerolift clean unmodified motorset, but have never personally used them. -S14 SR20 WaterPump 20 P.U. / 25 Shipped Bought a new water pump before disassembling the motor, and the old water pump looks brand-new inside. Might as well use the new one, so this one can go. Could essentially eat off it. Blades look great. -Chaser CF Kouki Hood - Cheap! Asking 200 (P.U. ONLY) This HAS to go. Seriously. Make me an offer. Got 2 hoods too many in the garage. Needs to leave soon. Perfect chance for a cheap Kouki conversion. The good: Great at heat management. After carwash, can see it fog up the window with the raised rear section. Helped keep my engine nice and cool at the beginner's clinic. (factory cooling system, never went above 180) Already drilled for AeroCatch latches. If you've had this done, you know this is a PITA/couple hours to get them perfect at a shop. Already drilled, ready to mount up new latches and go. AeroCatch's not included. The bad: Has the standard clearcoat cracks from trying to use the stock hood latch, as well as more clear cracks on the drivers headlight area from a deer impact. Was low speed, deer more "bounced". Didn't hurt the hood, just the clearcoat. -Stock SR manifold off my S14 SR. 50 P.U. / 60 Shipped -OEM Accordian 20 P.U. / 25 Shipped Got a Greddy, no longer need. I couldn't find any rips or tears. -OEM Heat shields 10 P.U. / 15 Shipped Wrapped Tomei mani and Coated turbo, no longer need. -OEM SR fly off my S14 SR -50 P.U. / 65 Shipped (Heavy....) Upgrading to lightweight, won't need. -OEM S14 Metal turbo gasket 10 P.U. / 15 shipped -10 OEM S14 SR20 Head Bolts (No washers) -10 P.U. / 15 Shipped. Yes, they're used. Yes, the FSM gives you the measurements for checking if you can reuse them, no I didn't measure them (don't have anything exact enough). I got a new set for cheap, so these can go. -BNIB OEM S14 SR20 Head Gasket 25 P.U. / 35 shipped Got this with my kit, but since gotten a MHG. Never installed. -BNIB OEM S14 SR20 Exhaust Manifold Gasket 15 P.U. / 25 shipped Came with kit, my Expreme manifold came with the 7 layer so no longer needed. Never installed.

05-19-2011, 11:16 AM	#2
BoostinIX Zilvia Addict Join Date: Feb 2008 Location: Laurel, MD Age: 39 Posts: 815 Trader Rating: (29) Feedback Score: 29 reviews	Bumpage!!! Will accept most reasonable offers. Need things gone. Last edited by BoostinIX; 05-19-2011 at 11:51 AM..

05-20-2011, 07:00 AM	#3
BoostinIX Zilvia Addict Join Date: Feb 2008 Location: Laurel, MD Age: 39 Posts: 815 Trader Rating: (29) Feedback Score: 29 reviews	Bump 2, come ooooooooon schwartz

05-22-2011, 03:51 AM	#4
Firebat060 Join Date: Dec 2007 Location: ATL Posts: 14 Trader Rating: (3) Feedback Score: 3 reviews	Pm sent. Interested in heat shields.

05-22-2011, 09:55 PM	#5
yongai27 Leaky Injector Join Date: Jan 2011 Location: Irvine Posts: 62 Trader Rating: (0) Feedback Score: 0 reviews	Do u have aerocatch pins for sale?