my s14 2jzgte build - Page 7 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

babillaracing · 03-01-2011, 03:12 PM

618whp and 492 ft/lbs at 22 psi on pump gas, will post video later

DHall243 · 03-01-2011, 03:27 PM

Nice numbers, Im looking for around the same next summer. Motors in the garage, Trans will be here Thursday.
Wished my car was as clean, its flat black as of now, I plan on letting people draw on it with a sharpie. lol

babillaracing · 03-01-2011, 04:23 PM

Quote:

Originally Posted by Boostfreak

Nice numbers, Im looking for around the same next summer. Motors in the garage, Trans will be here Thursday.
Wished my car was as clean, its flat black as of now, I plan on letting people draw on it with a sharpie. lol

Thank you sir and the car is no way clean

but it will be .here is the video . Have fun with your project sir
YouTube - 240sx 2JZ Dyno Run

babillaracing · 03-22-2011, 04:13 PM

ok ,thinking i had an overheating problem i decide to fab cooling panels for the radiator (i fab the side ones and bottom one, not the top center piece)
turn out this help some. car is running around 10 f cooler but what i had was'nt a cooling problem ,I had a mind problem lol . car never went over 195 at idle before the bigger intercooler and cams but after the install of those some times would get to around 208f at idle so i was thinking wtf . so i decide to do the panels so far stays at 198 f but i was reading the tsm that the supra auxiliary fans turn on at 212 f meaning the temp goes that high on a stock supra . anyway i gonna install an external oil cooler and change the mix of red toyota coolant. right now i have 50/50 . I think i gonna do 25% coolant and 75% distilled water (maybe a water wetter)

chris2jzgte · 02-06-2012, 05:16 PM

how hard was it to transfer the fuel lines from passenger to drivers side? any modifications needed to get this done?

turbociv910 · 02-06-2012, 09:45 PM

what size tires are those

babillaracing · 02-09-2012, 01:35 PM

Quote:

Originally Posted by chris2jzgte

how hard was it to transfer the fuel lines from passenger to drivers side? any modifications needed to get this done?

not hard at all

Quote:

Originally Posted by turbociv910

what size tires are those

275-50-15

HIGHFIVEBETA · 02-12-2012, 08:16 AM

Noice. Now time for new headlight lenses and repaint the bumper lol.

babillaracing · 02-14-2012, 05:59 AM

Quote:

Originally Posted by HIGHFIVEBETA

Noice. Now time for new headlight lenses and repaint the bumper lol.

i know man lol , but i gonna be swaping a 6 speed first .afterward i gonna paint the whole car and a new carbon fiber hood.

babillaracing · 03-02-2012, 07:38 AM

ok my weldon pump still at weldon and my friend need his weldon back so i decide to buy an 044 bosch to intalled on place on the weldon ,till i get mine back. when i get mine back i will install the bosch inside the fuel cell to do a surge tank

blkvip · 03-02-2012, 09:01 PM

awesome always wanted to do this to my old s14 lol

babillaracing · 03-03-2012, 06:21 AM

thanks sir

JDM SPUG · 03-13-2012, 08:45 AM

I was following this on supraforums. Nice build

DallasTXjdm · 03-21-2012, 05:50 AM

Hey Omar, I noticed you went with the ProEFI. How do you like it compared to the AEM V2? I am still trying to decide which one to go with along with the intake manifold. Some say Hyper and others say PHR, SP, or Virtual.

babillaracing · 03-21-2012, 06:26 AM

Quote:

Originally Posted by DallasTXjdm

Hey Omar, I noticed you went with the ProEFI. How do you like it compared to the AEM V2? I am still trying to decide which one to go with along with the intake manifold. Some say Hyper and others say PHR, SP, or Virtual.

i have'nt yet ,(big chunk of money lol) i am on my way to pick up a v160 (in georgia) thats were my money went lol .anyway when i sold my built r154 set up i get most of my money back. If i was you i go proefi (as long you got a tuner local ) aem sucks i wont get any aem product on my life. because they make promises that they never deliver .example flex fuel been put on hold for at least a year and customer support sucks balls.

DallasTXjdm · 03-21-2012, 10:01 AM

Quote:

Originally Posted by babillaracing

i have'nt yet ,(big chunk of money lol) i am on my way to pick up a v160 (in georgia) thats were my money went lol .anyway when i sold my built r154 set up i get most of my money back. If i was you i go proefi (as long you got a tuner local ) aem sucks i wont get any aem product on my life. because they make promises that they never deliver .example flex fuel been put on hold for at least a year and customer support sucks balls.

A couple of my buddies told me the same thing. I also noticed that most of the guys on SupraForums are running ProEFI or Haltechs. What type of intake manifold do you have bro? I can't tell. Man you are going to love the 6sp!!! I made sure I went with that on my swap.. a nice Getrag! Which flywheel are you going to use?

babillaracing · 03-22-2012, 08:11 AM

Quote:

Originally Posted by DallasTXjdm

A couple of my buddies told me the same thing. I also noticed that most of the guys on SupraForums are running ProEFI or Haltechs. What type of intake manifold do you have bro? I can't tell. Man you are going to love the 6sp!!! I made sure I went with that on my swap.. a nice Getrag! Which flywheel are you going to use?

pro-efi hands down .stock flywheel and clutch for now ,till i get some cash flow to go multi disc

uh oh

350 diff 3.35

babillaracing · 03-22-2012, 10:23 AM

more shit showing up

myndseye · 03-22-2012, 11:08 AM

You've built my car!!!! So its only fair I hijack your thread..mu ha ha ha haaa

great build!

babillaracing · 03-22-2012, 12:33 PM

Quote:

Originally Posted by myndseye

You've built my car!!!! So its only fair I hijack your thread..mu ha ha ha haaa

great build!

nice car sir, Thanks

Flicktitty · 03-22-2012, 12:59 PM

Whats your problems with the AEM? Just upset they don't offer a flex fuel setup? Or is there an actual issue with the tuning of your car?

I picked up an AEM V2 this year can't wait to try it.

babillaracing · 03-22-2012, 01:47 PM

Quote:

Originally Posted by Flicktitty

Whats your problems with the AEM? Just upset they don't offer a flex fuel setup? Or is there an actual issue with the tuning of your car?

I picked up an AEM V2 this year can't wait to try it.

before i bought aem i was undecided between aem v2 or proefi . i called aem and ask them about the flex fuel feature and they told me don't worry about flex fuel cause they were gonna release it in three months the latest . 2 years went by and nothing ,they even develope another box infinity something and left behind the v2 also i had a problem with the aem ,i email like 20 times their customer support and ver got a single reply back ,i post in their forum and nothing either

babillaracing · 03-22-2012, 07:46 PM

alex roque in action modifying my 350z diff cover to accept two studs instead of one

babillaracing · 03-23-2012, 09:28 PM

dss arrived ,Thanks Sam

gte block, guess you guys got the idea lol

JDM SPUG · 03-23-2012, 09:39 PM

What is the final drive on the 350z DIFF?

babillaracing · 03-24-2012, 06:25 AM

pm for that info

a little bit of elbow grease for the diff cover

florante rea · 03-24-2012, 08:51 AM

Nice work man, for me r154 for now, just too much money for the 6 speed.
Anyone tried marlin crawler rebuild kit for the r154? Im looking at that right now.

JDM SPUG · 03-24-2012, 10:50 AM

Omar had the marlin crawler R154

JDM SPUG · 03-24-2012, 10:52 AM

Quote:

Originally Posted by JDM SPUG

What is the final drive on the 350z DIFF?

Nvm just saw its a 3.35

DallasTXjdm · 03-24-2012, 12:54 PM

Bad ass Omar!!! Coming together nicely! How does your suspension look (Rear LCA, UCA, Traction Rods, Spring rate you ended up going with on the COs)? Any plans to go with meth?

03-01-2011, 03:12 PM	#181
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	618whp and 492 ft/lbs at 22 psi on pump gas, will post video later __________________ 618 whp tuned by alpha

03-01-2011, 03:27 PM	#182
DHall243 Leaky Injector Join Date: Jun 2009 Location: West Virginia Age: 33 Posts: 106 Trader Rating: (0) Feedback Score: 0 reviews	Nice numbers, Im looking for around the same next summer. Motors in the garage, Trans will be here Thursday. Wished my car was as clean, its flat black as of now, I plan on letting people draw on it with a sharpie. lol __________________ 1995 Nissan 240SX SE 2JZ w/R154

03-22-2011, 04:13 PM	#184
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	ok ,thinking i had an overheating problem i decide to fab cooling panels for the radiator (i fab the side ones and bottom one, not the top center piece) turn out this help some. car is running around 10 f cooler but what i had was'nt a cooling problem ,I had a mind problem lol . car never went over 195 at idle before the bigger intercooler and cams but after the install of those some times would get to around 208f at idle so i was thinking wtf . so i decide to do the panels so far stays at 198 f but i was reading the tsm that the supra auxiliary fans turn on at 212 f meaning the temp goes that high on a stock supra . anyway i gonna install an external oil cooler and change the mix of red toyota coolant. right now i have 50/50 . I think i gonna do 25% coolant and 75% distilled water (maybe a water wetter) __________________ 618 whp tuned by alpha

02-06-2012, 09:45 PM	#186
turbociv910 Zilvia Member Join Date: Oct 2011 Location: wilmington nc Age: 35 Posts: 241 Trader Rating: (0) Feedback Score: 0 reviews	what size tires are those __________________ www.carolinadyno.com s13 LSx turbo drag car- 1.42 60 ft, 6.32 1/8

03-02-2012, 07:38 AM	#190
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	ok my weldon pump still at weldon and my friend need his weldon back so i decide to buy an 044 bosch to intalled on place on the weldon ,till i get mine back. when i get mine back i will install the bosch inside the fuel cell to do a surge tank __________________ 618 whp tuned by alpha

02-06-2012, 05:16 PM	#185
chris2jzgte Join Date: Mar 2011 Location: United States Age: 32 Posts: 23 Trader Rating: (0) Feedback Score: 0 reviews	how hard was it to transfer the fuel lines from passenger to drivers side? any modifications needed to get this done?

02-12-2012, 08:16 AM	#188
HIGHFIVEBETA Zilvia Junkie Join Date: Jun 2011 Location: Where the wild things are, FL Posts: 327 Trader Rating: (4) Feedback Score: 4 reviews	Noice. Now time for new headlight lenses and repaint the bumper lol.

03-02-2012, 09:01 PM	#191
blkvip Join Date: Mar 2012 Location: boston Posts: 11 Trader Rating: (0) Feedback Score: 0 reviews	awesome always wanted to do this to my old s14 lol

03-03-2012, 06:21 AM	#192
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	thanks sir __________________ 618 whp tuned by alpha

03-13-2012, 08:45 AM	#193
JDM SPUG Zilvia Junkie Join Date: Mar 2011 Location: NY Posts: 345 Trader Rating: (7) Feedback Score: 7 reviews	I was following this on supraforums. Nice build

03-21-2012, 05:50 AM	#194
DallasTXjdm Zilvia Junkie Join Date: Sep 2011 Location: USA Posts: 581 Trader Rating: (41) Feedback Score: 41 reviews	Hey Omar, I noticed you went with the ProEFI. How do you like it compared to the AEM V2? I am still trying to decide which one to go with along with the intake manifold. Some say Hyper and others say PHR, SP, or Virtual.

03-22-2012, 10:23 AM	#198
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	more shit showing up __________________ 618 whp tuned by alpha

03-22-2012, 12:59 PM	#201
Flicktitty Post Whore! Join Date: Apr 2007 Location: Wisconsin Age: 37 Posts: 3,685 Trader Rating: (13) Feedback Score: 13 reviews	Whats your problems with the AEM? Just upset they don't offer a flex fuel setup? Or is there an actual issue with the tuning of your car? I picked up an AEM V2 this year can't wait to try it. __________________ 2JZ-GTE Swapped S13 Coupe - 1994 Supra Turbo

03-22-2012, 07:46 PM	#203
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	alex roque in action modifying my 350z diff cover to accept two studs instead of one __________________ 618 whp tuned by alpha

03-23-2012, 09:28 PM	#204
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	dss arrived ,Thanks Sam gte block, guess you guys got the idea lol __________________ 618 whp tuned by alpha

03-23-2012, 09:39 PM	#205
JDM SPUG Zilvia Junkie Join Date: Mar 2011 Location: NY Posts: 345 Trader Rating: (7) Feedback Score: 7 reviews	What is the final drive on the 350z DIFF?

03-24-2012, 06:25 AM	#206
babillaracing Zilvia Junkie Join Date: Oct 2009 Location: tampa Age: 47 Posts: 382 Trader Rating: (3) Feedback Score: 3 reviews	pm for that info a little bit of elbow grease for the diff cover __________________ 618 whp tuned by alpha Last edited by babillaracing; 03-24-2012 at 07:50 AM..

03-24-2012, 08:51 AM	#207
florante rea Zilvia FREAK! Join Date: Jan 2003 Location: king of prussia, pa Age: 43 Posts: 1,448 Trader Rating: (43) Feedback Score: 43 reviews	Nice work man, for me r154 for now, just too much money for the 6 speed. Anyone tried marlin crawler rebuild kit for the r154? Im looking at that right now. __________________ fdrea

03-24-2012, 10:50 AM	#208
JDM SPUG Zilvia Junkie Join Date: Mar 2011 Location: NY Posts: 345 Trader Rating: (7) Feedback Score: 7 reviews	Omar had the marlin crawler R154

03-24-2012, 12:54 PM	#210
DallasTXjdm Zilvia Junkie Join Date: Sep 2011 Location: USA Posts: 581 Trader Rating: (41) Feedback Score: 41 reviews	Bad ass Omar!!! Coming together nicely! How does your suspension look (Rear LCA, UCA, Traction Rods, Spring rate you ended up going with on the COs)? Any plans to go with meth?