Compatability thread (OEM upgrades) Full spectrum

[jspec240]

Compatibility thread... There are a lot of spread out threads of parts that will fit on on different chassis so I think this would be a good Idea to put em all on one thread. Its also here to help save money or make some on the forums. I know there will be

Please note any modifications needed if they are light or if there is a conversion and who makes it.

This is not Just for 240's its for any S and Z chassis, datsun as well as Infinity OEM compatable parts to and from them all.

Im also going to add Links for how too's and precise info. Heres a couple popular ones

The best s13/s14 300zx brake upgrade thread ever!!

The Definitive 300ZX Brake Swap!

VLSD Info for 240s

1. KA24DEvelopment.com :: VLSD Swap Information
2. 300ZX N/A (Z32) 4.083 ratio final drive swap (for a q45 upgrade)
3. Install Guide: Q45 Differential swap into 240SX subframe [Archive] - FreshAlloy.com Forums Q45 Diff info

Heres a list of what I know will fit on S13 and S14's, some are for KA turbo. A lot are well known but Id like to get the full spectrum.

Heres what I have gathered....

All contributors will have their screen name attached to this updated page...


(Duffman)
Z31 Turbo (non SS model) clutch type +4/87: works with open diff output flanges. Use S13 case and cover
(Bushido) Z31 Pad carrier for rear s13 calipers

300zx 90-96 N/A to s13/s14/s15/y32/y33

Calipers 26mm Aluminum (90 only) 91 & 92.5 early N/A and TT 30mm Aluminium, late 92.5-96 30mm iron both NA and TT - brake lines needed
rotors
MAF N62
BMC
Brake booster
Rear N/A Hubs
Rear aluminum uprights
Diff N/A has 4.08 gears can be used with pre 1/94 j30 or OEM 180sx axles
wheels
Ebrake assy coupled with R33 Brake lines (must have z32, or s14 5 lug rear hubs)
Transmission with Mazworks adapter plate

Z32 90 - 96 tt

injectors (370cc) purples
Calipers 26mm Aluminum (90 only) 91-96 30mm aluminium - brake lines needed
rotors
MAF N62
BMC
Brake booster
Rear Hubs
Rear aluminum uprights
Diff 3.9
wheels
Ebrake assy coupled with R33 Brake lines
Transmission with Mazworks adapter plate

y32 Q45 to s13/s14/sr20det vvt and non

Throttle body
370cc injectors (purples) only on the 94's
Ignitor chips
calipers
rotors
Rear hubs
Differential 3.54 gears need to change axles or output flanges for 6 bolt
for the 5 bolt j30 axles will fit in to the s13
Rear struts

y33 q45 97-01 to s13/s14

Calipers
Rotors
Rear hubs
Diff
Ignitors
Rear struts

Y34 q45 01-06 to s13/s14

calipers
rotors
Diff
Rear struts
Rear hubs

J30 to s13/s14

(Z28ricer) Front J30 5 lug hubs can be drilled out to fit OEM S13 bearings
Rear hubs/axles/and diff (need all to work)

z33 to s13/s14

Brembo brakes with an adapter
rotors

z34 to s13/s14
]
(Duffman)R34 torsen, GT-R non V-spec: unknown but I assume its 31mm 30 spline
brakes
rotors
wheels

r32 to s13/14/15

(Duffman) R32 and R33 GT-R only, non V-Spec clutch type: uses 31mm 30 spline output shafts. 3 out of 6 bolts line up (sort of) when using skyline output shafts or R230v output shafts (Q45 and turbo Z32).
calipers
rotors
seats

Eagle talon turbo 89-98
440cc Injectors (direct bolt in to for KA-T or S20DET)

rx7 FD to S13/S14
210 LPH fuel pump
Injectors but primary and secondary are different sizes

Supra - s13/s14

440 injectors will fit with a resistor pack and top feed rail

Sentra /SE-R spec-v to s13/s14
(EEK) Brembo calipers
(SWAYRAY) you'll need a 1mm spacer/washer to center the caliper w/ pads onto the rotor.... those spec-v rotors are very similar to the R33 GT-R w/ brembos only painted gold rather than black
(Stinky 180)the early 90s sentra ball joints are interchangeable

Maxima - s13
(Bushido) Rotors
(stinky_180) 90s maxima key ring light -> s13 (2 wires

S13 to s14/15

s14/15 Seats
s14/s15 Brakes
s14 KA Engine/tranny swaps over with minor mods
(EEK)s14/15 can use the s13 coilovers but must drill out the knuckle (Jspec240) must change the tops of the rear coilovers to the s13's

S15 SR swap Requires Drive line and diff if you want your speedo working
S15 Mirrors
s15 Steering wheel


S14 to s13 s15

s13 /s15 Seats front and rear
s13 Seat belts from both will work as manual belts
s13 Lower Control Arms are 15mm longer from s14
s14/s15 5 lug hubs ( need front spindles for s13 )
s15 rear seats
S15 to s13/14
s13 The s14 vlsd will fit with a quick change of the cover.

s15 SR swaps to both easily as dose the others however requires drive line and differential has the speedo instead of in the tranny.
s13/s14 Seats front and rear



This is off the top of my head. As posts are made (let me know if Im wrong as well) I will keep the info up to date on this first post so we wont have to search for them.

This was a short example so please if you know of any OEM part upgrades from other cars... POST EM UP

More to come