CO CP pistons, Eagle rods, etc redtop sr20det

[lutz5329]

First is my redtop SR20det that has been fully built from the bottom up. polished crank, decked block, bored .020 overbore, cp 86.5mm 8.5:1 compression, eagle rods, new bearings, new water pump, unorthodox crank pulley, everything also has been balanced with a fidanza lightweight flywheel, and also everything has been cryogenicly treated and I have the reciepts. DSCN1262 DSCN1270 For the top end it has HKS springs, hks cam gears, greddy valve stoppers, 3 angle vavle job, new bronze jim wolf valve guides for the exhaust side, arp head studs, cometic head gasket 86.5mm * .040". Also all was professionally done and also cryogenicly treated.
Also have a oem gasket kit for the intire engine. also have fmic with hot pipe and hks ssbov(need couplers and clamps). also a exedy stage 1 clutch pretty much brand new and fidanza flywheel. megan dump and downpipe. ecu, maf, wiring harness, manual trans, etc

I have everything for the swap except manual drive shaft, turbo and turbo manifold.


Price Breakdown: These are the prices I paid. I'm not expecting to get all my money back I know thats not going to happen.
CP pistons 500
Eagle rods 350
all bearings, machine work, balancing, and cryogenics for bottom end 1,125
gasket kit 200
arp headstuds 120
cometic head gasket 100
bronze valve guides 60
head work, 3 angle valve job,valve guide replace, cryo, everything check 430
HKS Cam gears 300, hks springs 250, I also have used hks step 2 I beleive 272 cams. but I'm not sure if their usable I paid 200
UD crank pulley 200
megan dumppipe 115 DSCN1167 megan downpipe 120
fidanza flywheel 300
exedy stage1 clutch 250
hks bov with hotpipe 250
fmic 200 DSCN1148 VLSD for s13 with shafts300 DSCN1147
ECU 100
Manual Trans 250
harness 100
total:5070
I'm trying to get 3500 OBO for everything for a swap(except turbo, manifold, and driveshaft. I'm also up for trades, I have a 3000gt vr4 so if you have anything let me know

I also have all the parts for the auto to manual swap (clutch pedal, master cyl, slave cyl, lines)
for this I'm looking for 180 OBO

Also DOHC pwer steering lines good condition 200 OBO

I also have a lot of stock parts like radiator, engine mounts, ac stuff, alternator, etc.

Also I got screwed from a person on here and bought an entire engine from him then found out that it was pretty messed up so I have a head that has nothing on it (springs, valves, etc.) and I believe some of the journals on the head for the cams are scratched and as of now it is not usable. but I also have (like a said above) hks cams that are step 2 272 and these cams are scratched in the journals as well. but I was thinking maybe some who knows a person with a machine shop could fix them because there worth over 200 each when there not damaged. But if anyones interested let me know and we can work something out. With the head I can also include stock springs and retainers and all that good stuff because I have two sets of head parts. these parts have also been cryogenicly treated for strength.

Just PM me and let me know what you need and I'll let you know if I have it.

I'm dont want to part out but if there is enough interest I might end up parting out. Thanks and let me know

I'll also try to put up more pics. I just dont have any on this comp.

[lutz5329]

please bump

[turbo-travis]

sending PM

[reccakun08]

so im guessing the head is not assembled with the block? is there an oil pan on the block right now?

[lutz5329]

I'm assembling it right now. It should be al together in about 2 weeks. I jsut torqued the head down and started cleaning the upper oil pan and oil pan. So yes it will be together soon. I just put up the thread to gauge interest.

[lutz5329]

bump please