|
Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars |
|
Thread Tools | Display Modes |
03-09-2010, 06:26 AM | #92 |
Nissanaholic!
Join Date: Mar 2006
Location: Philadelphia suburbs
Age: 39
Posts: 2,347
Trader Rating: (7)
Feedback Score: 7 reviews
|
^ Which disc are you running?
I am running the ACT 6-puck, heavy duty PP, and prolite flywheel (10.5 lbs). It looks like you went with the slightly heavier flywheel (I think that one was somewhere around 14 lbs?). Also, why the extreme pressure plate? That thing is gonna be a fucking stairmaster! The heavy duty PP + 6 puck can hold probably 420 ft-lbs of torque++ at the wheels..... My buddy has an extreme on his WRX, and every time I drive that, and then get in my car, it feels like my clutch is fucked up hahaha.
__________________
Daily driven |
03-09-2010, 08:30 AM | #93 | |
Zilvia Addict
Join Date: Jun 2008
Location: Orlando,FL
Age: 33
Posts: 651
Trader Rating: (13)
Feedback Score: 13 reviews
|
Quote:
LOL @ Stairmaster Im running an ACT 6 puck just like you lol. I picked ACT Extreme because I just wanted to get something pretty tuff that wont end up slipping in case i decided to change to a different set up later on. |
|
03-09-2010, 08:53 AM | #94 |
Zilvia Addict
|
That's the exact reason I didn't go with an ACT on my KA-T setup. I had a 2600 on my GSX and I felt like a I was gonna have road-rage every traffic jam. I went with a Competition Clutch with ultra-light flywheel (not sure of exact weight) and it's rated at 450rwtq. It feels 100X better/lighter than my old ACT setup. Either way, can't wait to see what #'s you put down. Goodluck!
|
03-09-2010, 11:16 AM | #96 | |
Zilvia Junkie
|
Quote:
gotta remember clutches are gonna feel totally different from car to car my nissan with the stage 3 spec is a feather my brothers mustang with the stage 3 spec is super tough to push in ps: how you been havent seen you in forever |
|
03-09-2010, 11:32 AM | #97 | |
Zilvia Junkie
Join Date: Jul 2006
Location: Nor VA
Age: 38
Posts: 500
Trader Rating: (0)
Feedback Score: 0 reviews
|
Quote:
thats bec. the mustang is more than likely cable not hydrualic system for the clutch release.. retarded design |
|
03-09-2010, 11:59 AM | #98 |
Zilvia Member
|
i think its just because its a mustang
__________________
SPEED KILLS!! Drive a Honda and live forever!! |
03-09-2010, 05:10 PM | #99 |
Zilvia FREAK!
Join Date: Jan 2008
Location: St. Maries, Idaho
Age: 35
Posts: 1,276
Trader Rating: (17)
Feedback Score: 17 reviews
|
i ran the unsprung version of this clutch it wasnt that bad. but this time i am doing the sprung version, just for longevity
__________________
My Twin Scroll Gt30r Sr22det Build |
03-22-2010, 07:39 PM | #101 |
Zilvia FREAK!
|
Let see some updates. I have the same goal as you, I will be rockin a bottom mount setup but on a KA-T.
|
03-22-2010, 09:53 PM | #102 |
Post Whore!
Join Date: Sep 2005
Location: SWFL
Age: 49
Posts: 3,318
Trader Rating: (3)
Feedback Score: 3 reviews
|
We want Food! Look at what you started! LOL!
I would like to see fitment, with the T04E compressor housing and 72ar Hot side (motor mount bracket, to compressor clearance). Oh yeah! with the tial44 fitted.
__________________
LoverTechnologies "Half Broken Things!" |
03-23-2010, 05:57 AM | #103 | ||
Zilvia Addict
Join Date: Jun 2008
Location: Orlando,FL
Age: 33
Posts: 651
Trader Rating: (13)
Feedback Score: 13 reviews
|
Quote:
Quote:
I also ordered Precision 1000cc injectors+ Resistors along with greddy top feed fuel rail it should be in a couple days from now. enjoy. |
||
03-23-2010, 05:11 PM | #105 | |
Zilvia Addict
Join Date: Jun 2008
Location: Orlando,FL
Age: 33
Posts: 651
Trader Rating: (13)
Feedback Score: 13 reviews
|
Quote:
This: edit: My DW740cc injectors will go to a KA-T project after this is done. Last edited by S13 curtis; 03-23-2010 at 05:21 PM.. Reason: E85 |
|
03-25-2010, 09:36 PM | #109 |
Zilvia FREAK!
Join Date: Jan 2008
Location: St. Maries, Idaho
Age: 35
Posts: 1,276
Trader Rating: (17)
Feedback Score: 17 reviews
|
i agree turbo fitment. i really want to do this with a gt3071 frame. and this exhaust housing
__________________
My Twin Scroll Gt30r Sr22det Build |
03-31-2010, 11:09 AM | #111 | |
Zilvia Addict
|
Quote:
funny..... i made 442rwhp on my stock block SR20 for almost 7 years.... i sold the entire engine setup and now its in a different chassis still ripping shit up.... its all in the tune! |
|
04-01-2010, 06:23 AM | #112 |
Zilvia Addict
Join Date: Jun 2008
Location: Orlando,FL
Age: 33
Posts: 651
Trader Rating: (13)
Feedback Score: 13 reviews
|
Well the 1000cc injectors and Jim Wolf Tech Resistors came in today also with the Greddy Fuel Rail. Those are Precision Injectors.
Also i dont have an update on the turbo fitment yet the only update i have is that the motor was pulled and the flywheel tranny and clutch were installed. I will post pics of the cut-out as soon as i can, the other update is that i ordered new intercooler pipes and im ditching the small steel pipes the old pipes were 2' hot side and 2.5 on the cold side and they were pretty shitty. Thenew pipes i just purchased are Aluminum and its 3 inch coldside and 2.5 hotside,air flowshould be better. I'm also going to get a new blowoff valve im not going to use my ssqv anymore, Im either going with the new Tial Q Blow off valve which is the one im leaning towards or the Greddy type r blow off valve. I would like to have your input on what you guys think for the BOV,thanks. Last edited by S13 curtis; 04-01-2010 at 07:38 AM.. |
04-01-2010, 07:51 AM | #114 | |
Nissanaholic!
Join Date: Mar 2006
Location: Philadelphia suburbs
Age: 39
Posts: 2,347
Trader Rating: (7)
Feedback Score: 7 reviews
|
Quote:
I am considering going with that turbine housing, and then I would go with the new MV-R Tial (44mm version of the MV-S.....very low profile, 44mm V-band flanged) but I have no idea if it would hit the strut tower... I recall someone discussed this somewhere, earlier....basically, it's okay for the coldside to be a little bigger, but you never want it smaller than the hotside (just what I heard).
__________________
Daily driven |
|
04-01-2010, 08:02 AM | #115 | |
Zilvia Addict
Join Date: Jun 2008
Location: Orlando,FL
Age: 33
Posts: 651
Trader Rating: (13)
Feedback Score: 13 reviews
|
Quote:
Tial 50mm Q BOV OR thats what i narrowed it down to, i got tired of my HKS ssqv . Since the tranny is on hopefully it wont be long before the turbo is mounted i want to see it just as bad as you guys do. |
|
04-01-2010, 08:06 AM | #116 |
Zilvia Junkie
Join Date: Oct 2006
Location: Aurora, CO
Age: 39
Posts: 375
Trader Rating: (13)
Feedback Score: 13 reviews
|
Not sure why so many people are hating on the stock bottom end. IIRC, Martin (ex-XAT guy, now with Zfever) is pushing a stock bottom end (I think, stock rods for sure though) to 500whp YouTube - Fever Racing s14.5 on Dyno Race Gas
Also, the Tial is miles better than the greddy imo. |
04-01-2010, 01:46 PM | #117 |
Zilvia Member
|
well i read some where that stock rods r forged steel so stock rods r fine
__________________
SPEED KILLS!! Drive a Honda and live forever!! |
04-02-2010, 05:56 AM | #118 |
Nissanaholic!
Join Date: Mar 2007
Location: Ft. Lauderdale
Age: 37
Posts: 1,776
Trader Rating: (12)
Feedback Score: 12 reviews
|
I was just looking into this wg - this sounds like the answer for this setup. Any idea when its going to be released? I cant seem to find any pricing info or finished pics.
__________________
|
04-02-2010, 06:16 AM | #119 | |
Nissanaholic!
Join Date: Mar 2006
Location: Philadelphia suburbs
Age: 39
Posts: 2,347
Trader Rating: (7)
Feedback Score: 7 reviews
|
Quote:
It may make a difference, may not. It is maybe like an inch or 1.5 inches shorter than the previous version, so if it wasn't even close in the first place, this won't make a difference.
__________________
Daily driven |
|
04-02-2010, 02:16 PM | #120 |
Zilvia FREAK!
Join Date: Jan 2008
Location: St. Maries, Idaho
Age: 35
Posts: 1,276
Trader Rating: (17)
Feedback Score: 17 reviews
|
i read something about the expansion of the air going out of the intercooler into a 3 inch pipe when it comes in from a smaller pipe also helps drop the temp of the air going into the engine.
i wonder how hard it would be to geta bottom mount tubular manifold and weld o na External gate flange up a in the same location as on a top mount manifold seems liek it should would good
__________________
My Twin Scroll Gt30r Sr22det Build |
Bookmarks |
|
|