Small Questions Thread (SEARCH FIRST! Use this instead of making NEW threads)

[soreballz]

Originally Posted by TrueFreshness

Im about to replace my tranny fluid. KA24 with 5 spd. How many quarts will I need?

2.4L

Originally Posted by yomisiu

Im going 5-lug for my s14.

bought z32 5 lug rear hubs since they're supposedly the same as s14 se hubs.

wondering which rotors would i need? s14 se for the rears or z32 rotors for the rears?

The hubs are the same (so long as they're N/A hubs, as the TT hubs use a larger axle). S14 SE rotors are what you need. Or you could use Altima rotors with Z31 caliper brackets (they're larger in diameter).

http://zilvia.net/f/archive-faqs/291...-calipers.html

[yomisiu]

awesome. thanks, soreballz! (lol@name) but really, thanks

[proxx]

Originally Posted by proxx

ok, i have new plugs wires and i replaced a shot injector, it also has a new cat, i cant get past 1/3 throttle with my car bogging down and sputtering most the time. It happen usually above 2500rpm, im thinking bad fuel pump what do you guys think?

checked ecu codes, and got code "55" which is a everything is ok code. timing is good and no vacuum leaks.


any help?

[JasianBlazin]

Anyone know how to remove stubborn over spray? I have tried clay bars and brake fluid it removed some of it but the over spray is still very visible.

[katsu_sauce]

i have a question:

i have a base model 96' s14, with only power window and window lock switches. i recently purchased door wire harnesses for both drivers and passenger sides and i have a set of new window,door lock, and window lock switches. what i really want to know is there anything else im missing to do the conversion? ie; fuses, plugs? help me please.

[Trickynick89]

Just wondering if the OEM "jdm" s14 kouki rear valances only come in FRP or are there urirhane ones....

[ZenkiKid]

Anybody run a 15/16 BMC off of a z31 on stock brakes?

I read on NRR that it helps the rear lock up even harder/easier.

[S14kouki_10]

Any one know How to identify a helical from an open diff by pictures?

[heaterlif3]

Besides ebay, I checked craigslist, could anyone tell me a good site or refer me to someone currently selling a upper and lower wire harnessing for a sr20det. Thank you very much for reading. my email is [email protected] feel free to email me a good site to try to find one or a link to a person selling one. again thank you very much

[e1_griego]

Originally Posted by S14kouki_10

Any one know How to identify a helical from an open diff by pictures?

See the extra set of worm gears? That's how you identify a helical.

[tengo240]

What is the size and thread pitch for the three bolts and one nut needed to bolt in seats in a s13? Thanks

[alonroz]

Hi,
would a 17X8 +38 wheels fit an S14? previously mounted on an EVO8, i know there are some offset issues, will i need spacers / longer wheel studs etc?
i now it won't look the best but still...
thanks,
Al

[harrypotter]

Originally Posted by JasianBlazin

Anyone know how to remove stubborn over spray? I have tried clay bars and brake fluid it removed some of it but the over spray is still very visible.

Brake or carb/choke cleaner. But it will damage your clear coat! I do it all the time on my car, then just wax the area after.

[JasianBlazin]

Originally Posted by harrypotter

Brake or carb/choke cleaner. But it will damage your clear coat! I do it all the time on my car, then just wax the area after.

Ok cool, will it make the clear coat discolored?

[dpritchard4]

is a soch and doch chassis harness the same??? im doing a fuse box relocation on my vert with sr swap (wiring specailties wiring) and wondering if can use an old harness and still drive my car. anyone know for sure what is different?


Edit- its the engine room harness are they the same in a soch and doch

[bc.]

Can i lift the sr20 out of my car with the straps wrapped around the intake and exhaust manifold?

[dpritchard4]

Yes u can, but i wouldnt recomend it. Thats alot of stress on the bolts threaded into the aluminum block

[codyace]

Originally Posted by JasianBlazin

Anyone know how to remove stubborn over spray? I have tried clay bars and brake fluid it removed some of it but the over spray is still very visible.

Wet Sand the area works too. Sometimes a polishing compound helps too.

Originally Posted by heaterlif3

Besides ebay, I checked craigslist, could anyone tell me a good site or refer me to someone currently selling a upper and lower wire harnessing for a sr20det. Thank you very much for reading. my email is [email protected] feel free to email me a good site to try to find one or a link to a person selling one. again thank you very much

www.wiringspecialities.com

Originally Posted by bc.

Can i lift the sr20 out of my car with the straps wrapped around the intake and exhaust manifold?

Yup!

[EsChassisLove]

Originally Posted by bc.

Can i lift the sr20 out of my car with the straps wrapped around the intake and exhaust manifold?

Cody said yes....but man that sounds sketch to me lol

[Grocery Cart]

Long story short.
I've got 2 s14s in my back yard, one's wrecked one I'm parting out. Just got my s13.

Will I have everything I need to put the s14 5 lug on the s13.
I've looked this up and everyone beats around the bush. No direct answer.

So yes or no, will I be able to put the s14 5 lug on the s13? What all will I need to take off and replace?

[S14DB]

Originally Posted by Grocery Cart

Long story short.
I've got 2 s14s in my back yard, one's wrecked one I'm parting out. Just got my s13.

Will I have everything I need to put the s14 5 lug on the s13.
I've looked this up and everyone beats around the bush. No direct answer.

So yes or no, will I be able to put the s14 5 lug on the s13? What all will I need to take off and replace?

On the front, Take the Strut, Knuckle and Control arm off the S14 together and bolt them onto the S13. Keep the S13 T/C rods and steering arms.
On the rear, Unbolt the axle nut and the 4 bolts holding the Hub/bearing assembly onto the knuckle. Transfer the Hub/Bearing assembly.

[Grocery Cart]

Originally Posted by S14DB

On the front, Take the Strut, Knuckle and Control arm off the S14 together and bolt them onto the S13. Keep the S13 T/C rods and steering arms.
On the rear, Unbolt the axle nut and the 4 bolts holding the Hub/bearing assembly onto the knuckle. Transfer the Hub/Bearing assembly.

No idea why it was so hard for someone to give me that simple of an answer! Haha

Thanks!

I've got ss brake lines as well, will they fit on my s13?

[S14DB]

Originally Posted by Grocery Cart

No idea why it was so hard for someone to give me that simple of an answer! Haha

Thanks!

I've got ss brake lines as well, will they fit on my s13?

Most SS lines are for 89-98.

[dpritchard4]

is a soch and doch engine room harness the same??? im trying to do a fuse box relocation on my vert with sr swap (wiring specailties wiring) and wondering if can use it. Im a rookie when it comes to electrical.

[heaterlif3]

anyone know besides ebay,craigslist if anyone is selling sr20det full wire harness? i cant locate any for under 200 dollars, let me know if you come across any or if there is a easy way to make my own for cheap

[soreballz]

Originally Posted by dpritchard4

is a soch and doch engine room harness the same???

Nope. They're different.

[S14kouki_10]

Could you tell if this is a helical lsd by these?

[Mangudai]

I should be purchasing a vented gas cap(as oppose to a non vented) correct?

[chiboy002]

yes
itll relieve tank pressure

[bc.]

Originally Posted by codyace

Yup!

Originally Posted by EsChassisLove

Cody said yes....but man that sounds sketch to me lol

I just pulled it tonight and it held up fine, I did detach the trans though so it was only motor.

Originally Posted by S14kouki_10

Could you tell if this is a helical lsd by these?

The dude on the same page you posted this picture, posted a picture of a helical and these look identical... lol, did you scroll up before you posted this?