TOB and other parts for blitz active single

[red_240]

I have a lightly used Blitz active single I purchased over a year ago. I'm having a hard time finding a definitive answer on what parts to get and where.

What I need is the TOB, sleeve, pressure plate bolts and flywheel bolts. So far through my research I have found that the blitz active single is identical to the ORC super single and a few others but I can't confirm if the TOB, sleeve and other parts are identical.

I seem to find different answers everywhere, some people say that the stock TOB and sleeve will work others say the opposite. I did find this post from 2008 reguarding an ORC TOB and sleeve but I'm not 100% sure he is referring to single disk and if he is I'm not 100% sure if the parts will work with my blitz:

Originally Posted by lok

you can get the TOB and sleeve from nissan.

*The release bearing outer diameter is 67,1mm.
*And, this release bearing is also the original of NISSAN.
*NISSAN original parts number is "30502-14601".
Therefore, You can also buy it from NISSAN.

And then, the sleeve bearing is only assembly in ORC.
The sleeve bearing assembly type of ORC is B type.
*You are not able to buy the individual of sleeve bearing from ORC.
*However, this sleeve bearing is also the original of NISSAN.
*NISSAN original parts number is "30501-N1600".
Therefore, You can also buy it from NISSAN.

Here is the link to the thread http://zilvia.net/f/showthread.php?t=172312

If anyone who has first hand knowledge and can give me a push in the right direction it would be greatly appreciated.

[red_240]

Bump. .

[jedi03]

have you contacted the manufacturer to ask?

[s13silvia123]

sure if you want

[red_240]

Originally Posted by jedi03

have you contacted the manufacturer to ask?

As far as I know blitz clutches is no longer in business.

Originally Posted by s13silvia123

sure if you want

What?

[RB25GUY]

Originally Posted by red_240

As far as I know blitz clutches is no longer in business.

ORC is the manufacture that makes Blitz clutches, super single 409 are the parts that are interchangeable

[Teambadrun]

ok i know loads about these clutches
you need to measure your standard clutch height bolted against a flywheel, basically how you do it is bolt the clutch asif it was on an engine to the flywheel on a bench, then put a vernier down the centre of it touching the base of the fingers / and bottom of the bench
telll me your height there and i will tell you which TOB carrier you need

for the bearing its a koyo rct4067l1.
I have loads in stock dude they are cheap
thanks

[CompleteXen]

Originally Posted by RB25GUY

ORC is the manufacture that makes Blitz clutches, super single 409 are the parts that are interchangeable

+1, same parts. Just grab an ORC TOB for the 409 and you will be set.

[red_240]

Thanks for the replies everyone, I received an instant message from lok that reads;

Originally Posted by lok

TOB / SLEEVE
Use the pn from my post that you found or buy this from frsport. I know it says twin but will work for the super single type clutch.

http://www.frsport.com/FRSPORT-1134-...T_p_13605.html

Pressure plate bolts

Use any grade 8 hardware Allen head with lock washer and you will be fine. You will probably have to go online because if I remember they are a weird size combination. M8x1.5 instead of 1.25

Flywheel bolts

Use stock and put some lock tight.

All torque specs are the same as factory for assembly.

From what you guys are saying it seems like this info may be incorrect, I'm not trying to bash Lok but I want to make sure I get the correct part. Maybe some one can verify that the above part is in fact what I need or not.

If someone can provide me with a link to the 409 TOB and sleeve I would appreciate it because after an hour of searching around I can't seem to find any place that sells them.

Unfortunately I can't take any measurements yet because I plan swapping the clutch when I swap the engine (current SR20 has low comp) and I don't want to pull it until I have all the parts I need to complete the job and the clutch is just a part of that.

[CompleteXen]

Bearing only - http://www.rhdjapan.com/orc-release-bearing-a-type.html

Bearing & Sleeve - http://www.rhdjapan.com/orc-release-...aring-set.html

Look through RHDJapan next time, their search sucks but you can find it with enough effort.

[RB25GUY]

Lok messaged you the right one....

[TheRealSy90]

RHDJapan typically has everything for these jdm clutches. Except the different depth TOB sleeves, they are just oem parts that are found in a thread here.

[red_240]

Originally Posted by CompleteXen

Bearing only - http://www.rhdjapan.com/orc-release-bearing-a-type.html

Bearing & Sleeve - http://www.rhdjapan.com/orc-release-...aring-set.html

Look through RHDJapan next time, their search sucks but you can find it with enough effort.

I found this when I first started looking but the bearing and sleeve doesn't seem to specify if it's for single or twin disk or even the 409. It says in the description to specify the model clutch I have but I can't find an option or text area to specify. I guess I just need to order and hope for the best? Anyways thank you for the help guys I really appreciate it.

[RB25GUY]

Originally Posted by red_240

I found this when I first started looking but the bearing and sleeve doesn't seem to specify if it's for single or twin disk or even the 409. It says in the description to specify the model clutch I have but I can't find an option or text area to specify. I guess I just need to order and hope for the best? Anyways thank you for the help guys I really appreciate it.

No on RHDJapan you tell them what clutch, transmission its in the check out section. They will get you the right products.

[TheRealSy90]

Yep, when you are checking out there will be a NOTES section as some point, there you'll want to verify everything you can regarding your parts you need. They will get you the right stuff. Very good people.