AR (or TX) KA-T KA24DE partout - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

FlatBlaack · 10-01-2013, 01:42 PM

Located in Fayetteville, Arkansas, but will be moving to Austin, Texas soon if that's closer to anyone. Prices are firm.

The engine has a blown headgasket, blew #4.

I'm not parting out the shortblock unless you want it shipped and are willing to pay the full price for the assembled shortblock. I'd rather not take it apart if at all possible.

Here's what's available:

Can make 'package deals' if you are looking to buy several things. Buyers pay shipping. I *REALLY* don't want to ship the block, so you'll have to accommodate me if you want that to happen.

CP pistons Crower 625+ rods ARP heads/mains/bolts
Ported head, 3-angle valve job, new valve seals
$1400

Megasquirt 2 Extra
LC-1 Wideband controller and sensor
$600 comes with wiring harness/cables/diagrams

GM Yukon (D585) Coil on Plug setup
S14 Distributor (with 50mm DIYAT trigger wheel)
$120 for COP setup (with triggerwheel)

S14 Distributor (stock)
$50

11 pound Fidanza 250mm flywheel
350Z 250mm clutch/Pressure plate
$450

Stock intake manifold with blocked off EGR ports, comes with Throttle Body/sensor
$100
3.5 bar (50 psi) external fuel pressure regulator
$80

Freshly rebuilt T3/T4 T04B H-Trim, full 2.5" exhaust with 4 bolt (garret-style) downpipe, 3" stainless steel turbo muffler
$500 for turbo + exhaust, $300 for turbo only

(2) S14 transmissions. One came out of the car while it was running, not sure of the other.
$100 for good tranny - Stainless steel clutch slave line + new slave cyl will go with it $40 for unknown trans

Also have a stock starter
$50
power steering pump
$30
Upgraded Maxima Alternator, drilled out tabs for use in the 240SX, modified upper bracket
$60

IAP tubular Mani SOLD
Z31 300ZX T3 turbo SOLD
JGS 38mm Wastegate SOLD
Front Mount Intercooler setup (FMIC) SOLD
stainless steel oil feed lines SOLD
JGS engine mounts SOLD
JGS polyurethane transmission mount SOLD

Rich260z · 10-01-2013, 02:53 PM

what do you have planned now? I've been following your builds for awhile

FlatBlaack · 10-01-2013, 02:55 PM

Most likely sit on the funds from the part out, and buy a C5 Corvette next summer.

A guy was going to buy the entire shell minus engine/trans, but he's probably flaked out, so I might just say screw it and put an aluminum 5.3L in the S14.

Moving to Austin this weekend though, so I'm not sure how much time/space I'll have for a full-bore project car. Stay tuned, I'll be around I'm sure

FlatBlaack · 11-01-2013, 08:57 AM

Would anyone be interested in the shortblock or ported head separately? I'm pulling the head next weekend to remove the blown headgasket.

All prices are OBO

abcdefg123 · 09-10-2014, 03:25 PM

Still have transmission?

s14sfreakaleak · 09-10-2014, 06:54 PM

sell just the head?

vinnyjdm · 09-25-2014, 09:51 PM

price for flywheel shipped to 60502?

95240sxs14 · 09-26-2014, 07:10 AM

I am interested in the block and the head. Not really looking to pay close to $1400, I know the parts and everything in it artent cheap. Not sure how long you will have this but I am going to arkansas in Nov for thanks giving. I'll be driving through Dallas, maybe I can make a trip down through Austin to pick it up if you will still have it.

10-01-2013, 01:42 PM	#1
FlatBlaack Join Date: Jan 2012 Location: NW Ark Age: 38 Posts: 10 Trader Rating: (0) Feedback Score: 0 reviews	(or TX) KA-T KA24DE partout Located in Fayetteville, Arkansas, but will be moving to Austin, Texas soon if that's closer to anyone. Prices are firm. The engine has a blown headgasket, blew #4. I'm not parting out the shortblock unless you want it shipped and are willing to pay the full price for the assembled shortblock. I'd rather not take it apart if at all possible. Here's what's available: Can make 'package deals' if you are looking to buy several things. Buyers pay shipping. I *REALLY* don't want to ship the block, so you'll have to accommodate me if you want that to happen. CP pistons Crower 625+ rods ARP heads/mains/bolts Ported head, 3-angle valve job, new valve seals $1400 Megasquirt 2 Extra LC-1 Wideband controller and sensor $600 comes with wiring harness/cables/diagrams GM Yukon (D585) Coil on Plug setup S14 Distributor (with 50mm DIYAT trigger wheel) $120 for COP setup (with triggerwheel) S14 Distributor (stock) $50 11 pound Fidanza 250mm flywheel 350Z 250mm clutch/Pressure plate $450 Stock intake manifold with blocked off EGR ports, comes with Throttle Body/sensor $100 3.5 bar (50 psi) external fuel pressure regulator $80 Freshly rebuilt T3/T4 T04B H-Trim, full 2.5" exhaust with 4 bolt (garret-style) downpipe, 3" stainless steel turbo muffler $500 for turbo + exhaust, $300 for turbo only (2) S14 transmissions. One came out of the car while it was running, not sure of the other. $100 for good tranny - Stainless steel clutch slave line + new slave cyl will go with it $40 for unknown trans Also have a stock starter $50 power steering pump $30 Upgraded Maxima Alternator, drilled out tabs for use in the 240SX, modified upper bracket $60 IAP tubular Mani SOLD Z31 300ZX T3 turbo SOLD JGS 38mm Wastegate SOLD Front Mount Intercooler setup (FMIC) SOLD stainless steel oil feed lines SOLD JGS engine mounts SOLD JGS polyurethane transmission mount SOLD __________________ 96 KA-T 9.0:1, E85, T04B H trim, MegaSquirt2 Extra, HLSD, coilovers, etc.

10-01-2013, 02:55 PM	#3
FlatBlaack Join Date: Jan 2012 Location: NW Ark Age: 38 Posts: 10 Trader Rating: (0) Feedback Score: 0 reviews	Most likely sit on the funds from the part out, and buy a C5 Corvette next summer. A guy was going to buy the entire shell minus engine/trans, but he's probably flaked out, so I might just say screw it and put an aluminum 5.3L in the S14. Moving to Austin this weekend though, so I'm not sure how much time/space I'll have for a full-bore project car. Stay tuned, I'll be around I'm sure __________________ 96 KA-T 9.0:1, E85, T04B H trim, MegaSquirt2 Extra, HLSD, coilovers, etc.

10-01-2013, 02:53 PM	#2
Rich260z Zilvia Addict Join Date: Apr 2011 Location: Burbank, CA Posts: 621 Trader Rating: (8) Feedback Score: 8 reviews	what do you have planned now? I've been following your builds for awhile

11-01-2013, 08:57 AM	#4
FlatBlaack Join Date: Jan 2012 Location: NW Ark Age: 38 Posts: 10 Trader Rating: (0) Feedback Score: 0 reviews	Would anyone be interested in the shortblock or ported head separately? I'm pulling the head next weekend to remove the blown headgasket. All prices are OBO __________________ 96 KA-T 9.0:1, E85, T04B H trim, MegaSquirt2 Extra, HLSD, coilovers, etc.

09-10-2014, 03:25 PM	#5
abcdefg123 Leaky Injector Join Date: Aug 2014 Location: downtown Posts: 133 Trader Rating: (0) Feedback Score: 0 reviews	Still have transmission?

09-10-2014, 06:54 PM	#6
s14sfreakaleak Join Date: Aug 2014 Location: CA Posts: 41 Trader Rating: (0) Feedback Score: 0 reviews	sell just the head?

09-25-2014, 09:51 PM	#7
vinnyjdm Zilvia Addict Join Date: Aug 2012 Location: Chicago Posts: 916 Trader Rating: (11) Feedback Score: 11 reviews	price for flywheel shipped to 60502?

09-26-2014, 07:10 AM	#8
95240sxs14 Join Date: Aug 2014 Location: San diego Age: 36 Posts: 31 Trader Rating: (0) Feedback Score: 0 reviews	I am interested in the block and the head. Not really looking to pay close to $1400, I know the parts and everything in it artent cheap. Not sure how long you will have this but I am going to arkansas in Nov for thanks giving. I'll be driving through Dallas, maybe I can make a trip down through Austin to pick it up if you will still have it.