TX Full SR part out!! Aftermarket, stock, suspension, etc! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

deedilus · 06-08-2011, 02:51 PM

Parting out my S13 redtop missile car, need money for a tow car for my 350z and don't need the missile car anymore. All prices are OBO, I know some are kinda high thats cause of low ballers. Shoot me an offer. Serious buyers only, really need this stuff gone ASAP!

For a faster response, call/text: (210) 863-7933 my name is Matt

* I'll be adding more/better pictures and items shortly, these were a bit rushed so I could just get everything up… I have two red tops that are torn apart so whatever was on them is for sale here, I know I missed things so if you need something and you don't see it on here PM me and I'll see if I have it.

SR20/S13:

Resurfaced SR20 head with everything including Cometic caps (cams, rockers, etc. included, dirty right now from being in the vicinity of us drilling the block for the oversized head studs, will re-clean it for you): $300
S13 SR20 Block with clevite bearings and ARP oversized headstuds (One or two head stud holes still need to be heli-coiled, I'll even throw in the entire oil pan) SOLD
S13 SR20 Block, perfect candidate for someone who is wanting to bore out they're motor, had a cracked piston and pretty sure it had a rod knock (I got scammed on the motor so I don't know), you can see where the piston was slapping around in the cylinder… JUST the block: $20 and it's yours..
SR20 rods: SOLD
SR20 oil squirters: $5
SR20 Crankshaft: SOLD
SR20 Oil pump w/ brand new filter: $40
SR20 Oil Pump: $35
SR20 Thermostat (x2): $15
SR20 distributor: $40
Cometic street pro bottom and top end gasket kit: $100
Generic intake pipe w/ A'pexi filter: $55
Stock MAF: $30
Xcess Power FMIC with all piping. blow off valve & hot pipe: $350 PENDING SALE
Without BOV & hotpipe: $200
Greddy Type S BOV with hotpipe: $150
Edge 3" Downpipe: $80
Edge Turbo elbow: $60
SR20 Coil Packs (no harness, already sold it) : $50
SR20 dipstick $10
SR20 timing chain: $10
SR20 front cover (x2): $20 each
SR20 upper oil pan: $30
SR20 lower oil pan: $20
eBay aluminum radiator + 1 3.5L Taurus fan: $150 Pending sale
Mishimoto Radiator hoses: $60
AiResearch T3 Turbo (pretty much .50 trim equiv, I never used it but has barely any shaft play, from what I've heard that's normal on these turbos): $220
Stock T25 w/ inlets outlets and all that good stuff… works but blades are very sketchy, needs rebuild really soon: $40
SR Injectors: $100Pending Sale
SR Valve cover (will finish getting the purple off of it for you): SOLD
S13 SR Engine Harness: $200 Pending sale
SR throttle body: $30
SR intake manifold: Make an offer
SR20 Alternator with a baller pulley: $70
Ichiba Top mount turbo manifold (bought it BNIB from someone on here, I still haven't used it either): SOLD
stock T25 sr20 exhaust manifold: $30
Mine's S13 SR20 ECU: SOLD
SR20 Starter: SOLD
SR water pump: $20
SR timing chain: SOLD
Creative Steel poly-urethane prototype motor mounts: $150
Stock SR20 mounts: $30
SR20 tensioner: $30
SR20 power steering pump: $40 SOLD
Generic eBay 3" N1 cat-back exhaust: SOLD
Generic Manual Boost Controller: $30
Walboro 255 fuel pump: SOLD
Spec Stage 1 Clutch (Just mounted on the car before we took the motor apart, never actually drove with it): $175
Working tranny, unknown miles with unknown short shifter: SOLD
Energy D1 spec poly-urethane master bushing kit: $150 shipped
Godspeed suspension kit (BNIB): $300 for all
-Front sway & rear sway: $110
-Camber arms: $60
-Toe arms: $60
-Pillow tension rods: $60
Autometer boost gauge: $35
Center AC vent 3-gauge pod: $10
Trust shift knob: SOLD
Speedhut Revolution Tachometer with customizable graduating shift light NEVER BEEN USED! Super nice, was going to use with my V8 350Z swap but never happened: $125

VH45/Q45:

Q45 throttle cable: $20
Q45 Throttle pedal: $20

VQ35/350Z:

03 - 05 350Z Engine Bay wiring harness: $300 shipped
04 350Z Main Engine harness: $300

deedilus · 06-08-2011, 03:57 PM

Bump for a note on the Creative Steel motor mounts: My friend got the first prototype of their poly-urethane motor mounts for his VQ35 S14. I helped put them in. After we finished, his motor (which use to move a lot), was completely still even while revving. But after riding in it it's not rough at all, you can't even tell that the motor is stiffer, it feels fantastic. These are the second incarnations of those motor mounts and are more heat resistant and last longer. They felt fantastic with the SR20, but I didn't really get to use them that much. If you get them I ask that you PLEASE stay in touch and give me updates on how they feel and how they are working so I can relay the info back to Creative Steel.

lucas240sx · 06-08-2011, 04:07 PM

Whats the mines ecu tune for?

nismoracingsx · 06-08-2011, 04:15 PM

Pics/info on the edge dp and elbow..
any hardware or gaskets or anything?
shipped to 31405
can't find the company on google, haven't heard of them before, but I could just be a noob..

deedilus · 06-08-2011, 04:22 PM

Quote:

Originally Posted by nismoracingsx

Pics/info on the edge dp and elbow..
any hardware or gaskets or anything?
shipped to 31405
can't find the company on google, haven't heard of them before, but I could just be a noob..

They have a website, I had trouble finding them in the first place, and they don't really sell to anyone yet. The only reason I got them is because I saw how they performed in my friends VQ s14. He knows the most about them I can ask him for more details if you're interested.

PMing you the other info ^_^

economix · 06-08-2011, 04:28 PM

If the exhaust isn't beat too badly and the starter atill works I'll take them both for $90 shipped to 16415 - just PM me when you're ready.

economix · 06-08-2011, 04:36 PM

Toss in the timing chain too for another $10, for an even $100 with the exhaust and starter.

Prez · 06-08-2011, 06:30 PM

subscribe bump

nomma · 06-08-2011, 09:09 PM

can you get pics of the godspeeds?

aalbert240 · 06-08-2011, 10:17 PM

Does the maf hav a pigtail??

deedilus · 06-09-2011, 12:21 AM

@lucas - PM'd

@Prez - Thanks! ^_^

@Nomma - Done, pictures added to first post.

@aalbert240 - the pigtail is currently on the engine harness.

NismoHead90 · 06-09-2011, 05:19 PM

yo matt, its cameron in SA, im gonna be doin a swap soon, was interested in the coil packs, dizzy, and the valve cover

deedilus · 06-09-2011, 08:59 PM

Cameron - better text me soon if you're interested cause I already got offers on both the coil packs and the valve cover ^_^

deedilus · 06-10-2011, 02:32 PM

Bump to the top! Hit me up, need this crap gone!

scrub__cleavin · 06-10-2011, 04:07 PM

Harness for sure.
what's the flow on the injectors?

Lil_D · 06-10-2011, 08:10 PM

Upper water neck and upper oil pan and tension rods shipped to 94583

Speed Junky · 06-11-2011, 04:14 PM

Quote:

Originally Posted by deedilus

Cameron - better text me soon if you're interested cause I already got offers on both the coil packs and the valve cover ^_^

Already sent payment for valve cover via Paypal.

deedilus · 06-17-2011, 03:59 PM

Sorry for the lack of responses from me, I work at a production company and I've literally been putting 12-13 hour days in since we have a movie coming up. Plus right after I head to the shop to try and get my Z done so I've had no time on my hands. PMing everyone now, Z is done so I have time back on my hands and getting caught up.

And had 2 Valve Covers, Speed snagged one then a local snagged the other. Sorry Cameron!

deedilus · 06-19-2011, 09:37 AM

Bump, for sale list updated. Hit me up!

sr20comic · 07-08-2011, 09:59 PM

how much for just the type s bov? and do you still have the sensors from the tranny?

will_drift_4_food · 07-09-2011, 08:35 PM

I need transmission mount and turbine outlet flange. SHipped to 30144.

bruins1 · 07-19-2011, 02:05 AM

Do you still have the sr20 upper oil pan???? if so please pm me.... i just need the little shield piece that goes on the outside bottom of the upper oil pan, it is held on by 2 little screws or bolts... it covers the hole where the flywheel can be seen when tranny is mounted.... if you do have it please pm me... thanks...

lilpiton · 07-19-2011, 02:05 PM

100 bux for RUCA and TOE LINKS?
and thanks for the coilpack harness, worked out perfect!

penco · 08-04-2011, 10:07 AM

pics of the radiator hoses?

AdamR · 08-04-2011, 10:58 AM

Would you seperate the t25 and the compressor inlet? I need just the inlet for the intake.

06-08-2011, 02:51 PM	#1
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Full SR part out!! Aftermarket, stock, suspension, etc! Parting out my S13 redtop missile car, need money for a tow car for my 350z and don't need the missile car anymore. All prices are OBO, I know some are kinda high thats cause of low ballers. Shoot me an offer. Serious buyers only, really need this stuff gone ASAP! For a faster response, call/text: (210) 863-7933 my name is Matt * I'll be adding more/better pictures and items shortly, these were a bit rushed so I could just get everything up… I have two red tops that are torn apart so whatever was on them is for sale here, I know I missed things so if you need something and you don't see it on here PM me and I'll see if I have it. SR20/S13: Resurfaced SR20 head with everything including Cometic caps (cams, rockers, etc. included, dirty right now from being in the vicinity of us drilling the block for the oversized head studs, will re-clean it for you): $300 S13 SR20 Block with clevite bearings and ARP oversized headstuds (One or two head stud holes still need to be heli-coiled, I'll even throw in the entire oil pan) SOLD S13 SR20 Block, perfect candidate for someone who is wanting to bore out they're motor, had a cracked piston and pretty sure it had a rod knock (I got scammed on the motor so I don't know), you can see where the piston was slapping around in the cylinder… JUST the block: $20 and it's yours.. SR20 rods: SOLD SR20 oil squirters: $5 SR20 Crankshaft: SOLD SR20 Oil pump w/ brand new filter: $40 SR20 Oil Pump: $35 SR20 Thermostat (x2): $15 SR20 distributor: $40 Cometic street pro bottom and top end gasket kit: $100 Generic intake pipe w/ A'pexi filter: $55 Stock MAF: $30 Xcess Power FMIC with all piping. blow off valve & hot pipe: $350 PENDING SALE Without BOV & hotpipe: $200 Greddy Type S BOV with hotpipe: $150 Edge 3" Downpipe: $80 Edge Turbo elbow: $60 SR20 Coil Packs (no harness, already sold it) : $50 SR20 dipstick $10 SR20 timing chain: $10 SR20 front cover (x2): $20 each SR20 upper oil pan: $30 SR20 lower oil pan: $20 eBay aluminum radiator + 1 3.5L Taurus fan: $150 Pending sale Mishimoto Radiator hoses: $60 AiResearch T3 Turbo (pretty much .50 trim equiv, I never used it but has barely any shaft play, from what I've heard that's normal on these turbos): $220 Stock T25 w/ inlets outlets and all that good stuff… works but blades are very sketchy, needs rebuild really soon: $40 SR Injectors: $100Pending Sale SR Valve cover (will finish getting the purple off of it for you): SOLD S13 SR Engine Harness: $200 Pending sale SR throttle body: $30 SR intake manifold: Make an offer SR20 Alternator with a baller pulley: $70 Ichiba Top mount turbo manifold (bought it BNIB from someone on here, I still haven't used it either): SOLD stock T25 sr20 exhaust manifold: $30 Mine's S13 SR20 ECU: SOLD SR20 Starter: SOLD SR water pump: $20 SR timing chain: SOLD Creative Steel poly-urethane prototype motor mounts: $150 Stock SR20 mounts: $30 SR20 tensioner: $30 SR20 power steering pump: $40 SOLD Generic eBay 3" N1 cat-back exhaust: SOLD Generic Manual Boost Controller: $30 Walboro 255 fuel pump: SOLD Spec Stage 1 Clutch (Just mounted on the car before we took the motor apart, never actually drove with it): $175 Working tranny, unknown miles with unknown short shifter: SOLD Energy D1 spec poly-urethane master bushing kit: $150 shipped Godspeed suspension kit (BNIB): $300 for all -Front sway & rear sway: $110 -Camber arms: $60 -Toe arms: $60 -Pillow tension rods: $60 Autometer boost gauge: $35 Center AC vent 3-gauge pod: $10 Trust shift knob: SOLD Speedhut Revolution Tachometer with customizable graduating shift light NEVER BEEN USED! Super nice, was going to use with my V8 350Z swap but never happened: $125 VH45/Q45: Q45 throttle cable: $20 Q45 Throttle pedal: $20 VQ35/350Z: 03 - 05 350Z Engine Bay wiring harness: $300 shipped 04 350Z Main Engine harness: $300 __________________ i like chicken nuggets Last edited by deedilus; 06-19-2011 at 09:37 AM..

06-08-2011, 03:57 PM	#2
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Bump for a note on the Creative Steel motor mounts: My friend got the first prototype of their poly-urethane motor mounts for his VQ35 S14. I helped put them in. After we finished, his motor (which use to move a lot), was completely still even while revving. But after riding in it it's not rough at all, you can't even tell that the motor is stiffer, it feels fantastic. These are the second incarnations of those motor mounts and are more heat resistant and last longer. They felt fantastic with the SR20, but I didn't really get to use them that much. If you get them I ask that you PLEASE stay in touch and give me updates on how they feel and how they are working so I can relay the info back to Creative Steel. __________________ i like chicken nuggets

06-08-2011, 04:15 PM	#4
nismoracingsx Zilvia Addict Join Date: Sep 2007 Location: Alachua, FL Age: 37 Posts: 969 Trader Rating: (32) Feedback Score: 32 reviews	Pics/info on the edge dp and elbow.. any hardware or gaskets or anything? shipped to 31405 can't find the company on google, haven't heard of them before, but I could just be a noob.. __________________

06-08-2011, 04:28 PM	#6
economix Zilvia Member Join Date: Feb 2011 Location: Erie, PA Posts: 185 Trader Rating: (5) Feedback Score: 5 reviews	If the exhaust isn't beat too badly and the starter atill works I'll take them both for $90 shipped to 16415 - just PM me when you're ready. __________________ 89 240SX w S14 SR20; 95 JDM 180SX S13 SR20; 09 Acura TL SH; 18 Jaguar XE S

06-08-2011, 04:36 PM	#7
economix Zilvia Member Join Date: Feb 2011 Location: Erie, PA Posts: 185 Trader Rating: (5) Feedback Score: 5 reviews	Toss in the timing chain too for another $10, for an even $100 with the exhaust and starter. __________________ 89 240SX w S14 SR20; 95 JDM 180SX S13 SR20; 09 Acura TL SH; 18 Jaguar XE S

06-08-2011, 04:07 PM	#3
lucas240sx Zilvia FREAK! Join Date: Sep 2006 Location: shawnee,okl Age: 37 Posts: 1,303 Trader Rating: (16) Feedback Score: 16 reviews	Whats the mines ecu tune for?

06-08-2011, 06:30 PM	#8
Prez Zilvia Junkie Join Date: Dec 2008 Location: Newark, Delaware Posts: 466 Trader Rating: (7) Feedback Score: 7 reviews	subscribe bump __________________ "soft so you can't even enjoy it"

06-08-2011, 09:09 PM	#9
nomma Join Date: Jan 2011 Location: fernandina beach fl Age: 38 Posts: 41 Trader Rating: (1) Feedback Score: 1 reviews	can you get pics of the godspeeds?

06-08-2011, 10:17 PM	#10
aalbert240 Zilvia Addict Join Date: Jan 2010 Location: santa paula Age: 35 Posts: 771 Trader Rating: (16) Feedback Score: 16 reviews	Does the maf hav a pigtail??

06-09-2011, 12:21 AM	#11
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	@lucas - PM'd @Prez - Thanks! ^_^ @Nomma - Done, pictures added to first post. @aalbert240 - the pigtail is currently on the engine harness. __________________ i like chicken nuggets

06-09-2011, 05:19 PM	#12
NismoHead90 Join Date: Feb 2010 Location: Houston Age: 32 Posts: 13 Trader Rating: (0) Feedback Score: 0 reviews	yo matt, its cameron in SA, im gonna be doin a swap soon, was interested in the coil packs, dizzy, and the valve cover __________________

06-09-2011, 08:59 PM	#13
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Cameron - better text me soon if you're interested cause I already got offers on both the coil packs and the valve cover ^_^ __________________ i like chicken nuggets Last edited by deedilus; 06-09-2011 at 11:01 PM..

06-10-2011, 02:32 PM	#14
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Bump to the top! Hit me up, need this crap gone! __________________ i like chicken nuggets

06-10-2011, 04:07 PM	#15
scrub__cleavin Join Date: Apr 2011 Location: Orlando Posts: 12 Trader Rating: (0) Feedback Score: 0 reviews	Harness for sure. what's the flow on the injectors?

06-10-2011, 08:10 PM	#16
Lil_D Zilvia Addict Join Date: Nov 2010 Location: The Bay Area Age: 31 Posts: 733 Trader Rating: (5) Feedback Score: 5 reviews	Upper water neck and upper oil pan and tension rods shipped to 94583

06-17-2011, 03:59 PM	#18
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Sorry for the lack of responses from me, I work at a production company and I've literally been putting 12-13 hour days in since we have a movie coming up. Plus right after I head to the shop to try and get my Z done so I've had no time on my hands. PMing everyone now, Z is done so I have time back on my hands and getting caught up. And had 2 Valve Covers, Speed snagged one then a local snagged the other. Sorry Cameron! __________________ i like chicken nuggets

06-19-2011, 09:37 AM	#19
deedilus Leaky Injector Join Date: Nov 2010 Location: Richmond, VA Posts: 103 Trader Rating: (5) Feedback Score: 5 reviews	Bump, for sale list updated. Hit me up! __________________ i like chicken nuggets

07-08-2011, 09:59 PM	#20
sr20comic Leaky Injector Join Date: Feb 2011 Location: ridgecrest Age: 34 Posts: 147 Trader Rating: (6) Feedback Score: 6 reviews	how much for just the type s bov? and do you still have the sensors from the tranny?

07-09-2011, 08:35 PM	#21
will_drift_4_food Join Date: Apr 2011 Location: Atlanta Posts: 16 Trader Rating: (0) Feedback Score: 0 reviews	I need transmission mount and turbine outlet flange. SHipped to 30144.

07-19-2011, 02:05 AM	#22
bruins1 Zilvia Member Join Date: Dec 2010 Location: Cali Age: 37 Posts: 197 Trader Rating: (9) Feedback Score: 9 reviews	yo!!! Do you still have the sr20 upper oil pan???? if so please pm me.... i just need the little shield piece that goes on the outside bottom of the upper oil pan, it is held on by 2 little screws or bolts... it covers the hole where the flywheel can be seen when tranny is mounted.... if you do have it please pm me... thanks...

07-19-2011, 02:05 PM	#23
lilpiton Zilvia Member Join Date: May 2008 Location: CHITOWN Age: 34 Posts: 155 Trader Rating: (7) Feedback Score: 7 reviews	100 bux for RUCA and TOE LINKS? and thanks for the coilpack harness, worked out perfect!

08-04-2011, 10:07 AM	#24
penco Zilvia Member Join Date: Feb 2008 Location: Milwaukee Age: 39 Posts: 249 Trader Rating: (1) Feedback Score: 1 reviews	pics of the radiator hoses?

08-04-2011, 10:58 AM	#25
AdamR Leaky Injector Join Date: Jan 2008 Location: Owensboro, KY Age: 40 Posts: 134 Trader Rating: (0) Feedback Score: 0 reviews	Would you seperate the t25 and the compressor inlet? I need just the inlet for the intake.