|
Chat General Discussion About The Nissan 240SX and Nissan Z Cars |
|
Thread Tools | Display Modes |
01-11-2023, 08:31 AM | #23821 |
Leaky Injector
|
If the crankshaft measurements are off, the crankshaft must be ground to match the oversized bearings. A competent machinist needed.
|
Sponsored Links |
01-26-2023, 09:24 AM | #23826 | |
Post Whore!
Join Date: Sep 2003
Location: Lake Stevens, WA
Age: 41
Posts: 2,657
Trader Rating: (20)
Feedback Score: 20 reviews
|
Quote:
You should direct this to the Want to buy section rather than the small questions thread. |
|
01-26-2023, 11:21 PM | #23828 |
Leaky Injector
|
|
01-27-2023, 07:16 AM | #23829 |
Post Whore!
|
As mentioned, if your crank shaft is out of spec, it will need to be ground to ?true? it. When that happens, the machine shop should be measuring the necessary tolerances. Oversized bearings are a must (thicker backing plate) to correct the variance in those tolerances. An align bore should also be considered if upgrading hardware.
__________________
*My SR20VET* Does your VTC gear rattle in your S14/15 SR? PM me. |
01-27-2023, 07:19 AM | #23830 |
Post Whore!
|
I have a cargo net from an S14 if you want it. I just need to find it.
__________________
*My SR20VET* Does your VTC gear rattle in your S14/15 SR? PM me. |
01-27-2023, 12:15 PM | #23831 |
Post Whore!
Join Date: Sep 2003
Location: Lake Stevens, WA
Age: 41
Posts: 2,657
Trader Rating: (20)
Feedback Score: 20 reviews
|
Passenger Side #26152-80F00
https://www.ebay.com/itm/304723637983 Driver Side #26157-80F00 https://nismoparts.nissanusa.com/p/N...157-80F00.html |
01-27-2023, 03:04 PM | #23833 |
Post Whore!
|
There?s not much to pm you. I need to find it and the mushroom mounts for it. I?ll message you once it has been uncovered.
__________________
*My SR20VET* Does your VTC gear rattle in your S14/15 SR? PM me. |
01-31-2023, 01:00 PM | #23835 |
Post Whore!
Join Date: May 2002
Location: Springfield, VA
Age: 42
Posts: 3,475
Trader Rating: (1)
Feedback Score: 1 reviews
|
I've got a high idle only when coming to a complete stop. Idle is set correctly with the TPS pulled, and is normal if I clutch in while coasting, but as soon as indicated speed drops to zero, it jumps up to around 250 rpm above where it should be for the engine temp.
It's an original 5 speed late '93 S13 KA. Mostly stock configuration except the PAIR system is removed. I'll try unplugging the EGR/EVAP solenoid to see if that's what's doing it, but the behavior seems opposite of what I'd expect if that circuit is the culprit - the solenoid should be open pretty much only while coasting down and closed otherwise. It's not a leaky brake booster or booster hose or check valve, nothing changes if I get on/off the brake pedal. It's entirely dependent on indicated speed. Power steering pressure sensor is installed and working. A/C is off (duh). My only other thought is someone somehow put an auto trans ECU in it for some reason and it's idling up because it thinks it's in Drive? I never bothered to look at the ECU ID. I only took it out once, way back in 2017 when I bought the car. Or could any of the manual transmission gear sensors have anything to do with it? It's got the reverse, neutral, 4th, and 5th sensors, reverse sensor works, one of the four seems to have a slight oil leak and I wonder if it's flaky. |
02-08-2023, 01:37 PM | #23837 |
Zilvia Junkie
Join Date: Mar 2016
Location: I n d i a n a
Age: 28
Posts: 349
Trader Rating: (0)
Feedback Score: 0 reviews
|
Most standard automobiles use an 18 gauge primary wire. Depending on your vehicle's original wiring, you might find that the typical wire gauge for the engine harness is 14-20 gauge. Copy and paste from this internet thing called Google
__________________
(づ。◕‿‿◕。)づ T E A M B L O O M |
02-09-2023, 03:15 AM | #23838 | |
Join Date: Aug 2022
Location: Philadelphia P.A.
Posts: 9
Trader Rating: (0)
Feedback Score: 0 reviews
|
Quote:
|
|
02-12-2023, 08:54 PM | #23841 |
Post Whore!
|
|
02-13-2023, 09:17 AM | #23843 |
Post Whore!
|
|
02-14-2023, 07:28 AM | #23844 |
Zilvia Addict
|
On this topic, is this idler pulley for SR the same piece as for KA? The dude I had pick up an SR AC bracket for me lost the pulley and bolt like an idiot but I have like 3 KA brackets/pulleys.
|
02-14-2023, 10:30 AM | #23845 | |
Post Whore!
Join Date: Sep 2003
Location: Lake Stevens, WA
Age: 41
Posts: 2,657
Trader Rating: (20)
Feedback Score: 20 reviews
|
Quote:
SR20DET S13 idler pulley #11925-65F03 SR20DET S14 idler pulley #11925-65F01 |
|
02-15-2023, 10:26 PM | #23846 | ||
Post Whore!
|
Quote:
Quote:
I can confirm the Dorman 89149 is correct for a RB20DET and RB25DET Neo. |
||
02-16-2023, 08:29 AM | #23847 |
Zilvia Addict
|
|
02-16-2023, 07:02 PM | #23848 | |
Post Whore!
|
Quote:
SR? I'd guess a B13 SER Sentra would be the same. RB starter, I back tracked the manufacturers part number. I think it's a Hitachi, turns out Mitsubishi Fork trucks use the EXACT SAME STARTER. Go from spending $500 to $65. |
|
02-19-2023, 05:17 PM | #23849 |
Post Whore!
Join Date: Sep 2003
Location: Lake Stevens, WA
Age: 41
Posts: 2,657
Trader Rating: (20)
Feedback Score: 20 reviews
|
https://page.auctions.yahoo.co.jp/jp...on/d1082362533
Has anyone tried these instead of the stock s-chassis door stopper? I see these all the time of Yahoo Japan Auctions and have been curious if this is a viable solution. My driver-side door squeals from stopper. I've checked around and Nissan discontinued them a bit ago. |
02-19-2023, 05:44 PM | #23850 | |
Post Whore!
|
Quote:
https://m.youtube.com/watch?v=VwKh3dFcv3Y https://trust-kikaku.myshopify.com/p...15-663101841s1
__________________
*My SR20VET* Does your VTC gear rattle in your S14/15 SR? PM me. |
|
Bookmarks |
Tags |
180sx type x kouki, 1jz, 2jz, 300zx, clutch, faq, ka24de, n/a, non-turbo, question, redtop s13 180sx silvia, s14, search, solenoid, starter, z32, zenki |
|
|