Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > Engine Tech

Engine Tech Technical discussion related to all relevant engines such as KA, SR, RB, CA, 2JZ , L24/26/28, VG, VQ, and LSx series.


Reply
 
Thread Tools Display Modes
Old 04-15-2020, 06:14 PM   #1
brn-n-jpn
 
brn-n-jpn's Avatar
 
Join Date: Dec 2009
Location: Marietta, PA
Age: 37
Posts: 10
Trader Rating: (0)
brn-n-jpn is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to brn-n-jpn
No spark after warming up

Anyone have any clue one what could be wrong...
So my cas works intermittently.
I plugged in my aem boost and oil pressure gauges one pin,like an idiot, over which cause a backed feed to the voltage regulator and cas to stop working. I then plugged gauges in correctly installed new alternator and another cas. Cranked the car with fuel pump unplugged to make sure there was spark. I then plugged fuel pump in and started the car. Everything was working fine until I noticed the car getting hot so I shut it off. Figured out that I unplugged radiator fan, once that was fixed I went to crank the car and NO SPARK.
I took one of my spare cas and plugged in with the key in the on position. While I'm spinning the cas gear by hand, the car has spark. But if I plug into the cas in the head no spark.
I pulled the cas from the head thinking it was bad but when I plug it in, have the key in the on position,and spin cas by hand I have spark.

Went to the garage today and cranked the car with original cas still in it and the car started right up.
I let the car warm up and fans cycled a few times then shut it off. Went to start it back up and no spark but if I plug spare cas in and spin the gear by hand it has spark.


Any ideas will be much appreciated before I burn this 9 year project to the ground.
brn-n-jpn is offline   Reply With Quote
Sponsored Links
Old 04-15-2020, 10:39 PM   #2
mechanicalmoron
Zilvia FREAK!
 
Join Date: Jul 2013
Location: tx
Posts: 1,078
Trader Rating: (0)
mechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nicemechanicalmoron is just really nice
Feedback Score: 0 reviews
See if you have a 5v when it's not sparking.
mechanicalmoron is offline   Reply With Quote
Old 04-17-2020, 02:58 AM   #3
anthony_240
Zilvia Junkie
 
anthony_240's Avatar
 
Join Date: Nov 2016
Location: Los Angeles
Age: 33
Posts: 489
Trader Rating: (3)
anthony_240 is an unknown quantity at this point
Feedback Score: 3 reviews
Check the pins/ wiring in the cas connector. With heat from the motor they could expand causing an open. If you have a dmm check resistance in wiring while cold then when hot.

Or you can cold start it and wiggle wiring around


Sent from my iPhone using Tapatalk
anthony_240 is offline   Reply With Quote
Reply

Bookmarks

Tags
cas timing sr20det cams, no spark, sr20, start up problems


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 02:57 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net