Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Chat

Chat General Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 01-12-2024, 11:28 PM   #991
slider2828
Post Whore!
 
slider2828's Avatar
 
Join Date: Oct 2004
Location: San Francisco, CA
Posts: 5,992
Trader Rating: (13)
slider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfection
Feedback Score: 13 reviews
OK kiddos.... for further driveline tuning, this thing makes a lot of noise if you don't do it right.... I would use CA18DET engine mounts or drift freaq mounts which sit the engine 10mm lower.... You then need to raise the tranny as high as you can.... In my car, when I did this..... the output of the tranny is pointing down -2.5* whereas my rest of the driveline -1.7*....

If you aren't sure how to do this...use this and an angle finder
https://spicerparts.com/calculators/...gle-calculator

or Tremec toolbox on your phone through any app store.... make sure you take your case off your phone to measure accurately.....
__________________
Turn and Burn!
slider2828 is offline   Reply With Quote
Sponsored Links
Old 01-16-2024, 01:14 AM   #992
slider2828
Post Whore!
 
slider2828's Avatar
 
Join Date: Oct 2004
Location: San Francisco, CA
Posts: 5,992
Trader Rating: (13)
slider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfection
Feedback Score: 13 reviews
Well shit for posterity and people tracking their cd009 my tranny started leaking in the bell housing. I didnt know this but some people say the bottom screw needs sealant....

In the end put fucking sealant on all the screws. I will probably use locktite blue that has built in thread sealant... geezus...

Will be pulling the tranny and changing, the input shaft seal, front housing seal and adding sealant on the screws... ugh...
__________________
Turn and Burn!
slider2828 is offline   Reply With Quote
Old 02-14-2024, 11:41 PM   #993
bl3ujay07
Zilvia Addict
 
bl3ujay07's Avatar
 
Join Date: Feb 2008
Location: norcal(209) and socal(805)
Posts: 690
Trader Rating: (6)
bl3ujay07 is an unknown quantity at this point
Feedback Score: 6 reviews
Quote:
Originally Posted by slider2828 View Post
Hey All,

Installed and it worked!!! The install was soooo easy. But you do need to remove the dash. Pulled constant 12v and acc 12v from the ignition tumbler. Then ground from anywhere. Then cut and wire in a wire from the dash (wire 6 y/lavendar) to speed 2 which is a sine wave and 16ppm setting.... now you have a gps and accelerometer speedo.

[img size=150]https://i.imgur.com/2iT0uXO.jpg[/img]
Thanks for sharing this! Your post led me to buy the same exact Dakota Digital unit along with the optional antenna. It?ll be nice to have a working Speedo again with a soon to swap Srvq kit.
bl3ujay07 is offline   Reply With Quote
Old 02-15-2024, 11:27 AM   #994
slider2828
Post Whore!
 
slider2828's Avatar
 
Join Date: Oct 2004
Location: San Francisco, CA
Posts: 5,992
Trader Rating: (13)
slider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfection
Feedback Score: 13 reviews
Quote:
Originally Posted by bl3ujay07 View Post
Thanks for sharing this! Your post led me to buy the same exact Dakota Digital unit along with the optional antenna. It?ll be nice to have a working Speedo again with a soon to swap Srvq kit.
Cool it works perfectly.... Very easy to wire... I forgot if I put it on Speed 1 or Speed 2..... and I used 20k PPM.... (I think its speed 2).

I have a kph jdm nismo cluster. But works perfectly.... Just doesn't work in a garage hahaha....
__________________
Turn and Burn!
slider2828 is offline   Reply With Quote
Old 02-15-2024, 05:35 PM   #995
bl3ujay07
Zilvia Addict
 
bl3ujay07's Avatar
 
Join Date: Feb 2008
Location: norcal(209) and socal(805)
Posts: 690
Trader Rating: (6)
bl3ujay07 is an unknown quantity at this point
Feedback Score: 6 reviews
Quote:
Originally Posted by slider2828 View Post
Cool it works perfectly.... Very easy to wire... I forgot if I put it on Speed 1 or Speed 2..... and I used 20k PPM.... (I think its speed 2).

I have a kph jdm nismo cluster. But works perfectly.... Just doesn't work in a garage hahaha....

Are you using the optional antenna for range? I have a dash cover with a ton of velcro to hold it down. I plan to mount the antenna in the center of the dash under the cover.

Also, your previous post mentioned using 16k PPM. Are you using the 20k PPM setting because of the kph cluster?
bl3ujay07 is offline   Reply With Quote
Old 02-16-2024, 10:20 AM   #996
slider2828
Post Whore!
 
slider2828's Avatar
 
Join Date: Oct 2004
Location: San Francisco, CA
Posts: 5,992
Trader Rating: (13)
slider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfectionslider2828 is close to perfection
Feedback Score: 13 reviews
Quote:
Originally Posted by bl3ujay07 View Post
Are you using the optional antenna for range? I have a dash cover with a ton of velcro to hold it down. I plan to mount the antenna in the center of the dash under the cover.

Also, your previous post mentioned using 16k PPM. Are you using the 20k PPM setting because of the kph cluster?
It could be because of KPH, that would make sense. Those are hardcoded PPMs in the module, so you can try a few settings.

I would assume under the cover is fine.... but I am not a radio technician so I have no idea..... I have to use the optional antennae because the module itself is setting behind the radio on the tranny tunnel. Its deep in the dash where there a lot of metal and radio antenna and grounding stuff...

I think the optional antennae under the dashboard cover overlay SHOULD work but its not very flat. Its about same thickness as a zippo lighter and about half the size.....
__________________
Turn and Burn!
slider2828 is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 09:29 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net