NY Type X partout, custom l.e.d headlights, built Ka-T, Endless 6piston, Type x shell, V - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

turbo_dreams · 10-17-2014, 04:35 PM

Wheels/Tires: $1800
Enkei Kojin
F: 18x9.5 +15
225/30/18 Toyota r888
R: 18x9.5 +22
245/35/18 Toyota r888

Engine Build (Parts/Machining/Labor): $3000
87.5mm supertech pistons eagle rods fully balanced to .25g w crank pulley lightened bullnosed crank alignhoned mains king std bearings ported head supertech springs locks and retainers OEM Nissan valve seals new oem shim buckets 3 angle valve job final lapped finish decked head and block to stock cams piston ring gap top .018" top .020" second ring OEM pump w shimmed relief valve OEM water pump sealed w threebond silicone oil drain in block chamfered copper coated cosmetic mls 88.0mm hg copper ARP head studs OEM chain guides OEM chain OEM tensioner full Nissan OEM gasket kit

Off road custom light bar l.e.d headlight/fabrication: $500

Rucas/toe rods/hotchkin sway bars front and back/es bushings/Nismo powerbrace: $700

Fujitsubo legalis R/Downpipe/test pipe: $800

Vmount setup (Koyo rad for an Rx7/Aluminum i.c for an Ae86/Aluminum piping/Fabricated by TMSPL, parts from 240motoring): $1000

Tial Q bov (red): $200

3475495890, I'm located in Queens NY but am willing to ship.

The shell is also fs. Shell consists of full oem type x kit I bought brand new, tubbed engine bay that's been shaved and painted Infiniti metallic silver. Just spent 5k on the paint job this past spring. All seam seal has been stripped and chassis has been stitch welded. Not a spot of rust, under chassis is freshly under coated by a body shop. This will be sold as a rolling shell that will just need a motor/trans. I have over 10k in my shell alone, I want 6k for my shell. This may come with some suspension goodies depending on how the partout goes.

jayrawr · 10-17-2014, 05:22 PM

Your car is so nice

turbo_dreams · 10-19-2014, 04:51 PM

Quote:

Originally Posted by jayrawr

Your car is so nice

Thank you.

Bump

iLagX · 10-19-2014, 05:01 PM

nice ka-t!! free bump

turbo_dreams · 10-21-2014, 04:24 PM

Brakes have been sold.

turbo_dreams · 10-25-2014, 12:01 PM

Bump

Msglength

turbo_dreams · 11-02-2014, 12:40 PM

Headlights, motor, rims, shell still available

Konster · 11-02-2014, 03:16 PM

If only the headlights were around $300 I'd buy be all over them.

turbo_dreams · 11-06-2014, 02:57 PM

Quote:

Originally Posted by Konster

If only the headlights were around $300 I'd buy be all over them.

Sorry, can't go that low.

Konster · 11-06-2014, 05:50 PM

Cool. Lmk if you change your mind. I can send it to you as a friend so you don't pay fees and pick it up since I'm right by Queens.

Mishkin_707 · 11-06-2014, 06:55 PM

How custom are those led headlights? They look like the L.E.D fog lights I have on my truck and they weren't $500

turbo_dreams · 11-06-2014, 07:25 PM

Quote:

Originally Posted by Mishkin_707

How custom are those led headlights? They look like the L.E.D fog lights I have on my truck and they weren't $500

If they weren't custom, you wouldn't be asking me.

killer240 · 11-06-2014, 09:29 PM

are you selling the seats? If so are they Zeta II?

turbo_dreams · 11-06-2014, 11:06 PM

Quote:

Originally Posted by killer240

are you selling the seats? If so are they Zeta II?

Sorry, they've been sold

speedgod^s13 · 11-08-2014, 05:48 PM

Pictures of what the headlight cutoff/output looks like?

turbo_dreams · 12-08-2014, 08:06 PM

Motor sold.

RB25GUY · 12-08-2014, 09:00 PM

Damn I wish this shell was a slicktop bump NY love

juhd · 12-08-2014, 10:05 PM

i was wondering if you were willing to just sell the bulb sockets for the turn signals. I bought used turn signals and all i have is the pigtail wiring. I cant find them online and my only option is to buy them used. So if youre willing to just sell me the bulb sockets i would really appreciate it. Thanks

702s13 · 12-08-2014, 10:19 PM

Very nice car man! Sorry I can't afford any of it lol, but I'm working on a similar led headlight set up, could you tell me the size off the light bars you are using?

abaron13 · 12-09-2014, 04:10 PM

Interested in the headlights. Do you have any more detailed pictures?

turbo_dreams · 12-15-2014, 04:44 PM

I don't mean to sound like a dick, but unless you're planning on buying my headlights please stop contacting me about dimensions and specs. These are the only pics I have, the price is set, and if I don't get it I'll be keeping them. Thanks

3475495890

speedgod^s13 · 12-15-2014, 07:06 PM

Quote:

Originally Posted by turbo_dreams

I don't mean to sound like a dick, but unless you're planning on buying my headlights please stop contacting me about dimensions and specs. These are the only pics I have, the price is set, and if I don't get it I'll be keeping them. Thanks

3475495890

Asking for light output pictures, wasn't unreasonable. What you are asking for those lights isn't chump change, so it's reasonable that people are going to ask questions/request pictures, etc. I know that there are a lot of tire kickers out there, but that is the price of selling an item. Just saying.

usdm180sx · 04-14-2015, 01:29 PM

I know the motor is sold, but please post pics of the leakdown/compression test results AFTER the motor was removed and BEFORE it was shipped out. Thanks

Bagdeez · 04-14-2015, 01:53 PM

Have any of the oem 180 you wanna sell?

EDacIouSX · 05-11-2015, 10:26 PM

Thanks for selling me this motor and faking the compression tests. "Advertised psi 150/150/150/150." Actual PSI: 120/120/0/30

These are my pictures after I discovered the motor wouldn't start upon installing it.

cylinder 3 0 psi

RalliartRsX · 05-11-2015, 10:30 PM

WOW! Open a dispute if possible

That is pretty shitty, geeezzz!

So fucking tired of the place, the scum and no protection for buyers. But hey, this place brings in traffic right??

So tired of hearing and seeing posts like above..........

BigKriss · 05-11-2015, 10:39 PM

That is just sooo wrong...bad news seller, real bad news...Only consolation here is that once you have rebuilt the engine you know its all good.

EDacIouSX · 05-11-2015, 10:57 PM

Quote:

Originally Posted by RalliartRsX

WOW! Open a dispute if possible

That is pretty shitty, geeezzz!

So fucking tired of the place, the scum and no protection for buyers. But hey, this place brings in traffic right??

So tired of hearing and seeing posts like above..........

Quote:

Originally Posted by BigKriss

That is just sooo wrong...bad news seller, real bad news...Only consolation here is that once you have rebuilt the engine you know its all good.

yea man... he claimed it blew when i tried to start it or that i ran my car.

10-17-2014, 04:35 PM	#1
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	Type X partout, custom l.e.d headlights, built Ka-T, Endless 6piston, Type x shell, V Wheels/Tires: $1800 Enkei Kojin F: 18x9.5 +15 225/30/18 Toyota r888 R: 18x9.5 +22 245/35/18 Toyota r888 Engine Build (Parts/Machining/Labor): $3000 87.5mm supertech pistons eagle rods fully balanced to .25g w crank pulley lightened bullnosed crank alignhoned mains king std bearings ported head supertech springs locks and retainers OEM Nissan valve seals new oem shim buckets 3 angle valve job final lapped finish decked head and block to stock cams piston ring gap top .018" top .020" second ring OEM pump w shimmed relief valve OEM water pump sealed w threebond silicone oil drain in block chamfered copper coated cosmetic mls 88.0mm hg copper ARP head studs OEM chain guides OEM chain OEM tensioner full Nissan OEM gasket kit Off road custom light bar l.e.d headlight/fabrication: $500 Rucas/toe rods/hotchkin sway bars front and back/es bushings/Nismo powerbrace: $700 Fujitsubo legalis R/Downpipe/test pipe: $800 Vmount setup (Koyo rad for an Rx7/Aluminum i.c for an Ae86/Aluminum piping/Fabricated by TMSPL, parts from 240motoring): $1000 Tial Q bov (red): $200 3475495890, I'm located in Queens NY but am willing to ship. The shell is also fs. Shell consists of full oem type x kit I bought brand new, tubbed engine bay that's been shaved and painted Infiniti metallic silver. Just spent 5k on the paint job this past spring. All seam seal has been stripped and chassis has been stitch welded. Not a spot of rust, under chassis is freshly under coated by a body shop. This will be sold as a rolling shell that will just need a motor/trans. I have over 10k in my shell alone, I want 6k for my shell. This may come with some suspension goodies depending on how the partout goes. __________________ www.tm-spl.com Kouki's & some apple juice. Last edited by turbo_dreams; 10-25-2014 at 07:26 PM..

10-17-2014, 05:22 PM	#2
jayrawr Zilvia FREAK! Join Date: Nov 2007 Location: 56Deuce Age: 36 Posts: 1,141 Trader Rating: (14) Feedback Score: 14 reviews	Your car is so nice __________________

10-19-2014, 05:01 PM	#4
iLagX Post Whore! Join Date: Dec 2008 Location: 626/714 Posts: 2,940 Trader Rating: (40) Feedback Score: 40 reviews	nice ka-t!! free bump __________________ PARTING OUT S13/S14 NEED PARTS PM ME!

10-21-2014, 04:24 PM	#5
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	Brakes have been sold. __________________ www.tm-spl.com Kouki's & some apple juice.

10-25-2014, 12:01 PM	#6
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	Bump Msglength __________________ www.tm-spl.com Kouki's & some apple juice.

11-02-2014, 12:40 PM	#7
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	Headlights, motor, rims, shell still available __________________ www.tm-spl.com Kouki's & some apple juice.

11-02-2014, 03:16 PM	#8
Konster Zilvia FREAK! Join Date: Jul 2012 Location: NY Age: 35 Posts: 1,273 Trader Rating: (19) Feedback Score: 19 reviews	If only the headlights were around $300 I'd buy be all over them. __________________ Hyer.

11-06-2014, 05:50 PM	#10
Konster Zilvia FREAK! Join Date: Jul 2012 Location: NY Age: 35 Posts: 1,273 Trader Rating: (19) Feedback Score: 19 reviews	Cool. Lmk if you change your mind. I can send it to you as a friend so you don't pay fees and pick it up since I'm right by Queens. __________________ Hyer.

11-06-2014, 06:55 PM	#11
Mishkin_707 Zilvia Addict Join Date: Jul 2009 Location: everywhere Age: 41 Posts: 732 Trader Rating: (1) Feedback Score: 1 reviews	How custom are those led headlights? They look like the L.E.D fog lights I have on my truck and they weren't $500

11-06-2014, 09:29 PM	#13
killer240 Post Whore! Join Date: Jun 2009 Location: Pair of dice, Norcal Age: 33 Posts: 2,621 Trader Rating: (24) Feedback Score: 24 reviews	are you selling the seats? If so are they Zeta II? __________________ REVIEW

11-08-2014, 05:48 PM	#15
speedgod^s13 Post Whore! Join Date: Nov 2004 Location: Honolulu, Hawaii Age: 44 Posts: 3,188 Trader Rating: (27) Feedback Score: 27 reviews	Pictures of what the headlight cutoff/output looks like?

12-08-2014, 08:06 PM	#16
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	Motor sold. __________________ www.tm-spl.com Kouki's & some apple juice.

12-08-2014, 09:00 PM	#17
RB25GUY Nissanaholic! Join Date: Feb 2013 Location: NY Age: 34 Posts: 2,033 Trader Rating: (9) Feedback Score: 9 reviews	Damn I wish this shell was a slicktop bump NY love

12-08-2014, 10:05 PM	#18
juhd Zilvia Junkie Join Date: Sep 2012 Location: San Diego Age: 29 Posts: 589 Trader Rating: (9) Feedback Score: 9 reviews	i was wondering if you were willing to just sell the bulb sockets for the turn signals. I bought used turn signals and all i have is the pigtail wiring. I cant find them online and my only option is to buy them used. So if youre willing to just sell me the bulb sockets i would really appreciate it. Thanks

12-08-2014, 10:19 PM	#19
702s13 Leaky Injector Join Date: May 2011 Location: Las Vegas Age: 36 Posts: 70 Trader Rating: (3) Feedback Score: 3 reviews	Very nice car man! Sorry I can't afford any of it lol, but I'm working on a similar led headlight set up, could you tell me the size off the light bars you are using? __________________ extrabolts are just weight reduction

12-09-2014, 04:10 PM	#20
abaron13 Zilvia Junkie Join Date: Mar 2011 Location: Cleveland Age: 32 Posts: 385 Trader Rating: (24) Feedback Score: 24 reviews	Interested in the headlights. Do you have any more detailed pictures?

12-15-2014, 04:44 PM	#21
turbo_dreams Zilvia FREAK! Join Date: Nov 2006 Location: queens, n.y Age: 33 Posts: 1,333 Trader Rating: (9) Feedback Score: 9 reviews	I don't mean to sound like a dick, but unless you're planning on buying my headlights please stop contacting me about dimensions and specs. These are the only pics I have, the price is set, and if I don't get it I'll be keeping them. Thanks 3475495890 __________________ www.tm-spl.com Kouki's & some apple juice.

04-14-2015, 01:29 PM	#23
usdm180sx Post Whore! Join Date: Dec 2005 Location: 562 Posts: 4,807 Trader Rating: (5) Rides Gallery: usdm180sx Feedback Score: 5 reviews	I know the motor is sold, but please post pics of the leakdown/compression test results AFTER the motor was removed and BEFORE it was shipped out. Thanks __________________ -Norm!

04-14-2015, 01:53 PM	#24
Bagdeez Leaky Injector Join Date: Sep 2014 Location: Wilsonville Age: 36 Posts: 101 Trader Rating: (0) Feedback Score: 0 reviews	Have any of the oem 180 you wanna sell?

05-11-2015, 10:26 PM	#25
EDacIouSX Post Whore! Join Date: Nov 2004 Location: Los Angeles Age: 38 Posts: 4,565 Trader Rating: (53) Rides Gallery: EDacIouSX Feedback Score: 53 reviews	Thanks for selling me this motor and faking the compression tests. "Advertised psi 150/150/150/150." Actual PSI: 120/120/0/30 These are my pictures after I discovered the motor wouldn't start upon installing it. cylinder 3 0 psi

05-11-2015, 10:30 PM	#26
RalliartRsX Post Whore! Join Date: Apr 2006 Location: Maryland Posts: 4,791 Trader Rating: (32) Feedback Score: 32 reviews	WOW! Open a dispute if possible That is pretty shitty, geeezzz! So fucking tired of the place, the scum and no protection for buyers. But hey, this place brings in traffic right?? So tired of hearing and seeing posts like above..........

05-11-2015, 10:39 PM	#27
BigKriss Leaky Injector Join Date: Dec 2012 Location: South Africa Posts: 141 Trader Rating: (0) Feedback Score: 0 reviews	That is just sooo wrong...bad news seller, real bad news...Only consolation here is that once you have rebuilt the engine you know its all good.