RB FAQ - Page 12 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

eh? · 04-25-2009, 08:28 AM

Quote:

Originally Posted by ProjNightshade

thanks, but I need 100% certainty before I start workin on this. anyone else have anything?

RB25 VSS will work with s14 speedo.

8gti9 · 04-25-2009, 06:34 PM

is the rb25det s1 same as the rb25det s2 wiring into a '91 s13?

ProjNightshade · 04-26-2009, 05:30 PM

Quote:

Originally Posted by eh?

RB25 VSS will work with s14 speedo.

thanks for the help. now what about the tach? haha.

eh? · 04-27-2009, 06:23 PM

Quote:

Originally Posted by ProjNightshade

thanks for the help. now what about the tach? haha.

There is a screw behind the tach that will adjust the RPM reading. You will need another reference for actual RPM though.

ProjNightshade · 04-27-2009, 10:52 PM

Quote:

Originally Posted by eh?

There is a screw behind the tach that will adjust the RPM reading. You will need another reference for actual RPM though.

ok cool. thanks!

dtowngoalie · 04-29-2009, 01:01 AM

Anybody know the difference between a cefiro rb20det and a skyline rb20det

soon2bs13 · 04-30-2009, 03:42 PM

Nissan Cefiro - Wikipedia, the free encyclopedia

skyvia25 · 05-25-2009, 06:56 PM

any one knows how to install the water tube into a gredy style intake manifold. my came seperated and it looks like its brass or copper. i took it to get it welded but the guy said he could n do it, i heard that u could just push it in with a rubber mallet, but min is to loose and it just goes in any ideas tnx..

*ANVIL* · 06-03-2009, 01:08 PM

coat it with a bunch of red high temp sealant and push it in, or go to your local home depot and get a peiece of tube that fits better and also coat it with sealant to prevent leaks

*Skyn* · 06-15-2009, 02:52 PM

im putting an rb20 in an S14
any suggestions on what i can pick off my Ka stuff and use with RB

and also which trans can go on it besides an rb one and suggestions on mounts or is this gonna be almost direct

eh? · 06-17-2009, 01:40 PM

Quote:

Originally Posted by Skyn

im putting an rb20 in an S14
any suggestions on what i can pick off my Ka stuff and use with RB

and also which trans can go on it besides an rb one and suggestions on mounts or is this gonna be almost direct

I'm pretty sure people have been using the stock KA xmember with RB mounts and you can use the stock driveshaft. You can use the KA radiator also. Only the RB bell housing will work so you can't use another tranny (unless you swapped the bell housing)

soon2bs13 · 06-29-2009, 06:46 PM

okay guys... my 240sx project is nearly completed. the major thing left to do is get it painted and figure out the wiring for the tach/speedometer.

anyone have a link that will help explain how to wire up the transmission to get the speedo/tach working? Am I just going to have to get an aftermarket Tach? I tried searching, but could not find what I was looking for. Maybe someone who has seen a thread before can point me in the right direction.

thanks!

maztamekanik · 06-30-2009, 06:57 PM

i need to no what kind of turbos my motor has if anyone can help id appreciate that

*bardabe* · 07-01-2009, 11:29 AM

post pictures

soon2bs13 · 07-03-2009, 01:29 AM

Quote:

Originally Posted by soon2bs13

okay guys... my 240sx project is nearly completed. the major thing left to do is get it painted and figure out the wiring for the tach/speedometer.

anyone have a link that will help explain how to wire up the transmission to get the speedo/tach working? Am I just going to have to get an aftermarket Tach? I tried searching, but could not find what I was looking for. Maybe someone who has seen a thread before can point me in the right direction.

thanks!

? anyone ?

eh? · 07-08-2009, 01:52 PM

Quote:

Originally Posted by soon2bs13

? anyone ?

See "lower harness prep"
RBforums - wiring
For the dash
LS Automotive - LS Products

myrbsrgig · 08-22-2009, 03:08 PM

Quote:

Originally Posted by drift freaq

well, my info is not false for a RB25 install. You did a 26 there are some differences in the installs. Since you feel your info is so ass kicking and superior share it. Instead of playing P.M. me in private, and playing it like your so superior.Almost sounds like a exercise in your ego. I am not saying it is but it comes off that way. If not I apologize in advance.

oh ya and for everyone. These installs have a number of ways to be done, depending on if you utilize a R33 GTST crossmember with the stock RB engine brackets, (which is what we do) or not.
We choose this particulare method because it allowed us with our Custom Urethane mounts to move the engine as far back and as low as possible in the S13 chassis.
Yes we did custom power steering lines,it works kick ass too!! I am in the process of finishing up my air, using a RB25 R33 air con compressor and fittings. All we had to do is have the lines extended to my stock lines coming from the firewall.
The only reason I say what I say is because compared to whats on the market our setup is cleaner and looks much more factory.
Ours will be a product not someones back yard job.

my question to u is is it possible to have a rb26 6-speed tranny with the awd in a 93 240...if it is what steps do i need to take in making that happen

*bardabe* · 09-06-2009, 01:12 AM

^^^ obviously if you have to ask its something you can't do so either you need lots of $$$ or lots of $$$. intense amount of fab work, and the getrag 6 speed alone will run more than 5K

jacob74 · 09-08-2009, 09:05 AM

Quote:

Originally Posted by myrbsrgig

my question to u is is it possible to have a rb26 6-speed tranny with the awd in a 93 240...if it is what steps do i need to take in making that happen

$$$

Making it AWD will cost lotssss and lots of $$. Just put a rb25 tranny on there. if you reaallly want a 6 speed, thenn..... well, fuck it. what do you need a 6 speed for? 45mph 6th gear pulls?

951's 330i · 10-07-2009, 12:25 AM

Quick, and probably stupid question, but theres no way to fit the downpipe from a company like hks onto our rb's in the s14 chasis right?

eklips3 · 10-07-2009, 02:18 AM

Quote:

Originally Posted by 951's 330i

Quick, and probably stupid question, but theres no way to fit the downpipe from a company like hks onto our rb's in the s14 chasis right?

nope . there are no downpipes that would fit straight from factory .

best thing to do is buy a downpipe , cut the flange where it connects to the o2 housing. the rotate the flange you cut a few degrees, then bolt it up to the o2 housing , mark it , the take it off and weld it together.

951's 330i · 10-07-2009, 01:22 PM

Quote:

Originally Posted by eklips3

nope . there are no downpipes that would fit straight from factory .

best thing to do is buy a downpipe , cut the flange where it connects to the o2 housing. the rotate the flange you cut a few degrees, then bolt it up to the o2 housing , mark it , the take it off and weld it together.

Thanks, i thought so. Anyone have experience with the syko performance elbow that they sell that i guess u can use any sr downpipe with?

eklips3 · 10-07-2009, 05:36 PM

Quote:

Originally Posted by 951's 330i

Thanks, i thought so. Anyone have experience with the syko performance elbow that they sell that i guess u can use any sr downpipe with?

syko performance downpipe is o2 housing plus downpipe combo so you dont have to cut, clock and reweld.

if you are just buying an SR downpipe then it goes back to you having to do a little custom work.

951's 330i · 10-08-2009, 03:02 AM

Quote:

Originally Posted by eklips3

syko performance downpipe is o2 housing plus downpipe combo so you dont have to cut, clock and reweld.

if you are just buying an SR downpipe then it goes back to you having to do a little custom work.

Ok thanks

Now i have a other question on a turbo timer i just bought. Which harness do i need to get? Its a hks TT but im not sure on which harness? Do i get the one that says silvia for the sr? Or the one that is meant for the skyline i think? Thanks

*GSXRJJordan* · 10-08-2009, 03:40 AM

Quote:

Originally Posted by 951's 330i

Ok thanks

Now i have a other question on a turbo timer i just bought. Which harness do i need to get? Its a hks TT but im not sure on which harness? Do i get the one that says silvia for the sr? Or the one that is meant for the skyline i think? Thanks

Turbo timer should match the car, not the engine. It installs in the ignition harness.

951's 330i · 10-08-2009, 04:09 AM

Quote:

Originally Posted by GSXRJJordan

Turbo timer should match the car, not the engine. It installs in the ignition harness.

Oh ok i see. So then i would need the one that says silvia s14 on their site right? This one

4103-RN001NISSAN Silvia S14 1993-1998 Turbo ; JDM Specific SR20DET Chassis

Yum-Yum · 10-08-2009, 02:15 PM

Quote:

Originally Posted by soon2bs13

? anyone ?

j30 tach works flawless.

951's 330i · 10-09-2009, 03:05 PM

Ok already made a thread about this. But after installing my turbo timer, the car wouldnt start. Electrics work but no start. Took the turbo timer off(harness) reconnected the starter how it should be and then the car starts again? What could be the problem with? On the starter there are six connections in the plug but on the harness there are only five connections for it. Im really stumped on this one.

*johngriff* · 10-09-2009, 07:05 PM

Check this out.

Now that the PFC for the RB is discontinued, Haltech has released a direct replacement ecu for the R32/R33 Engines / Cars. You can use the OEM MAF(S) or upgrade to MAP with this ecu, its really your choice.

Here is a link to haltech's site about it:
Platinum Pro R32 / R33 Plug-in - Haltech Engine Management Systems

MSRP Is about $1680

951's 330i · 10-15-2009, 12:21 AM

Whats a good, almost direct turbo? See that some people say there are turbos that are direct bolt ons but then right after say will need some fitment issues resolved? I see most people using the HKS GT2530 turbo.

Is this a straight bolt on with this turbo? Is the lag really bad? Or should i look for another turbo instead?

Thanks all

04-30-2009, 03:42 PM	#337
soon2bs13 Zilvia Junkie Join Date: Jun 2006 Location: TN Posts: 459 Trader Rating: (1)	Nissan Cefiro - Wikipedia, the free encyclopedia __________________ neg repping is cool!!

06-15-2009, 02:52 PM	#340
Skyn Premium Member Join Date: Feb 2009 Location: Las vegas nevada Posts: 271 Trader Rating: (3)	im putting an rb20 in an S14 any suggestions on what i can pick off my Ka stuff and use with RB and also which trans can go on it besides an rb one and suggestions on mounts or is this gonna be almost direct __________________ -1996 Rb20DET powered 240sx Se R.I.P. -89 s13 Ka-T (under construction -http://saisoku.mybrute.com -http://projectziptie.wordpress.com/

06-29-2009, 06:46 PM	#342
soon2bs13 Zilvia Junkie Join Date: Jun 2006 Location: TN Posts: 459 Trader Rating: (1)	okay guys... my 240sx project is nearly completed. the major thing left to do is get it painted and figure out the wiring for the tach/speedometer. anyone have a link that will help explain how to wire up the transmission to get the speedo/tach working? Am I just going to have to get an aftermarket Tach? I tried searching, but could not find what I was looking for. Maybe someone who has seen a thread before can point me in the right direction. thanks! __________________ neg repping is cool!!

06-30-2009, 06:57 PM	#343
maztamekanik Join Date: Jun 2009 Location: missouri Age: 23 Posts: 1 Trader Rating: (0)	1990 rb26dett turbos i need to no what kind of turbos my motor has if anyone can help id appreciate that

07-01-2009, 11:29 AM	#344
bardabe Performance Development Join Date: Aug 2005 Location: SoCali 951 Age: 20 Posts: 3,176 Trader Rating: (1) Rides Gallery: bardabe	post pictures __________________ BARDABE PERFORMANCE DEVELOPMENT Custom Fabrication, Wiring Services, and Parts Development Welded Diferentials, Lifetime Warranty no questions asked Review Thread

04-25-2009, 06:34 PM	#332
8gti9 Join Date: Apr 2009 Location: Tacoma, WA Posts: 19 Trader Rating: (0)	is the rb25det s1 same as the rb25det s2 wiring into a '91 s13?

04-29-2009, 01:01 AM	#336
dtowngoalie Join Date: Oct 2008 Location: York Age: 19 Posts: 3 Trader Rating: (0)	Anybody know the difference between a cefiro rb20det and a skyline rb20det

05-25-2009, 06:56 PM	#338
skyvia25 Join Date: Jan 2009 Location: OC-CA Age: 22 Posts: 32 Trader Rating: (0)	any one knows how to install the water tube into a gredy style intake manifold. my came seperated and it looks like its brass or copper. i took it to get it welded but the guy said he could n do it, i heard that u could just push it in with a rubber mallet, but min is to loose and it just goes in any ideas tnx..

06-03-2009, 01:08 PM	#339
ANVIL im a lion ROAR im a dinosaur Join Date: Apr 2005 Location: Anchorage, Alaska Posts: 763 Trader Rating: (6)	coat it with a bunch of red high temp sealant and push it in, or go to your local home depot and get a peiece of tube that fits better and also coat it with sealant to prevent leaks

09-06-2009, 01:12 AM	#348
bardabe Performance Development Join Date: Aug 2005 Location: SoCali 951 Age: 20 Posts: 3,176 Trader Rating: (1) Rides Gallery: bardabe	^^^ obviously if you have to ask its something you can't do so either you need lots of $$$ or lots of $$$. intense amount of fab work, and the getrag 6 speed alone will run more than 5K __________________ BARDABE PERFORMANCE DEVELOPMENT Custom Fabrication, Wiring Services, and Parts Development Welded Diferentials, Lifetime Warranty no questions asked Review Thread

10-07-2009, 12:25 AM	#350
951's 330i Leaky Injector Join Date: Jun 2009 Location: So Cal-Corona Posts: 126 Trader Rating: (2)	Quick, and probably stupid question, but theres no way to fit the downpipe from a company like hks onto our rb's in the s14 chasis right?

10-09-2009, 03:05 PM	#358
951's 330i Leaky Injector Join Date: Jun 2009 Location: So Cal-Corona Posts: 126 Trader Rating: (2)	Ok already made a thread about this. But after installing my turbo timer, the car wouldnt start. Electrics work but no start. Took the turbo timer off(harness) reconnected the starter how it should be and then the car starts again? What could be the problem with? On the starter there are six connections in the plug but on the harness there are only five connections for it. Im really stumped on this one.

10-09-2009, 07:05 PM	#359
johngriff @RPSport.net! Join Date: Jun 2004 Location: Long Beach, CA Posts: 4,042 Trader Rating: (4) Rides Gallery: johngriff	Check this out. Now that the PFC for the RB is discontinued, Haltech has released a direct replacement ecu for the R32/R33 Engines / Cars. You can use the OEM MAF(S) or upgrade to MAP with this ecu, its really your choice. Here is a link to haltech's site about it: Platinum Pro R32 / R33 Plug-in - Haltech Engine Management Systems MSRP Is about $1680 __________________ RPSport 949.891.1710 RPSport's New Products for the S13 and SR20! Join our Haltech Group Buy! John@RPSport.net

10-15-2009, 12:21 AM	#360
951's 330i Leaky Injector Join Date: Jun 2009 Location: So Cal-Corona Posts: 126 Trader Rating: (2)	Whats a good, almost direct turbo? See that some people say there are turbos that are direct bolt ons but then right after say will need some fitment issues resolved? I see most people using the HKS GT2530 turbo. Is this a straight bolt on with this turbo? Is the lag really bad? Or should i look for another turbo instead? Thanks all

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://zilvia.net/f/tech-talk/90376-rb-faq.html
Posted By	For	Type	Date	Hits
Engine Oil Filter Part Numbers, 2007 Honda Civic Si Oil Filter Location, Motorcycle Oil Filter Remote - Sienna	This thread	Refback	03-13-2009 05:19 AM	1
anyoen done rb25 on s13? - Beyond.ca - Car Forums	This thread	Refback	07-29-2008 02:37 AM	1