Noob wheel fitment help with MB battles - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

slipandflow · 03-03-2011, 12:37 PM

I have a stock s14 and want to put on mb battles 17x9.5. I know I have to fender roll but do I have to fender roll too if I run with factory spec for camber? also running 235/35/17 front and 235/45/17 rear.

*turbo2nr* · 03-03-2011, 12:40 PM

you should be fine with just a roll with 235/40/17 all around

i was running
17x9.5+15 235/40/17 f (-2.1)
17x9.5+15 255/40/17 r (-2.4)

i rolled all around no pull

btw check out rimtuck.com you can find ppl with similar setup's there, or the wheel filament thread here ..

Forge_55b · 03-03-2011, 12:57 PM

you didn't mention offset so hard to really say

slipandflow · 03-03-2011, 01:43 PM

oops sorry +15.
Turbo2nr: and they sit flush? camber isnt that bad right?

*turbo2nr* · 03-03-2011, 01:50 PM

yup they sit really flush you could tell they were cambered from the back but it wasnt too bad..

slipandflow · 03-03-2011, 02:17 PM

hows the tire wear though?

*turbo2nr* · 03-03-2011, 02:41 PM

can give a full review but it will vary upon tire and wear rating..

i had yoko s-drive and i had maybe around 10k on all four tires and it maybe wore around 20% middle and outside and ~35% inside.. not to much different..

stock 240sx is cambered in from the factory fyi.. -2.5 is the limit of factory tolerance as per alignment rack

slipandflow · 03-03-2011, 04:02 PM

yeah they are cambered factory. Thanks a lot bro. Helped a lot.

towlie · 03-05-2011, 07:21 PM

Stock fenders, roll no pull. No spacer. S13

17x9.5 +15

Fits alright lol. Battles are very stock fender friendly

*upsdude* · 03-05-2011, 08:26 PM

i had 245/40/17's on my old bronze battles(17x9.5 +15) and had poke like a mother lol...they stuck out like 3/4" to 1"

03-03-2011, 12:37 PM	#1
slipandflow Zilvia Member Join Date: Nov 2010 Location: Elk Grove Posts: 259 Trader Rating: (3) Feedback Score: 3 reviews	Noob wheel fitment help with MB battles I have a stock s14 and want to put on mb battles 17x9.5. I know I have to fender roll but do I have to fender roll too if I run with factory spec for camber? also running 235/35/17 front and 235/45/17 rear.

03-03-2011, 12:40 PM	#2
turbo2nr s14 baus Join Date: Jan 2005 Location: queens NYC Age: 27 Posts: 1,852 Trader Rating: (7) Feedback Score: 7 reviews	you should be fine with just a roll with 235/40/17 all around i was running 17x9.5+15 235/40/17 f (-2.1) 17x9.5+15 255/40/17 r (-2.4) i rolled all around no pull btw check out rimtuck.com you can find ppl with similar setup's there, or the wheel filament thread here .. __________________ s14 kouki ka-t tm-spl.com http://zilvia.net/f/builds-builds-on...0hp-build.html instagram @jai_p

03-03-2011, 01:50 PM	#5
turbo2nr s14 baus Join Date: Jan 2005 Location: queens NYC Age: 27 Posts: 1,852 Trader Rating: (7) Feedback Score: 7 reviews	yup they sit really flush you could tell they were cambered from the back but it wasnt too bad.. __________________ s14 kouki ka-t tm-spl.com http://zilvia.net/f/builds-builds-on...0hp-build.html instagram @jai_p

03-03-2011, 02:41 PM	#7
turbo2nr s14 baus Join Date: Jan 2005 Location: queens NYC Age: 27 Posts: 1,852 Trader Rating: (7) Feedback Score: 7 reviews	can give a full review but it will vary upon tire and wear rating.. i had yoko s-drive and i had maybe around 10k on all four tires and it maybe wore around 20% middle and outside and ~35% inside.. not to much different.. stock 240sx is cambered in from the factory fyi.. -2.5 is the limit of factory tolerance as per alignment rack __________________ s14 kouki ka-t tm-spl.com http://zilvia.net/f/builds-builds-on...0hp-build.html instagram @jai_p

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-03-2011, 12:57 PM	#3
Forge_55b Zilvia Junkie Join Date: Jun 2007 Location: OC Age: 31 Posts: 409 Trader Rating: (2) Feedback Score: 2 reviews	you didn't mention offset so hard to really say

03-03-2011, 01:43 PM	#4
slipandflow Zilvia Member Join Date: Nov 2010 Location: Elk Grove Posts: 259 Trader Rating: (3) Feedback Score: 3 reviews	oops sorry +15. Turbo2nr: and they sit flush? camber isnt that bad right?

03-03-2011, 02:17 PM	#6
slipandflow Zilvia Member Join Date: Nov 2010 Location: Elk Grove Posts: 259 Trader Rating: (3) Feedback Score: 3 reviews	hows the tire wear though?

03-03-2011, 04:02 PM	#8
slipandflow Zilvia Member Join Date: Nov 2010 Location: Elk Grove Posts: 259 Trader Rating: (3) Feedback Score: 3 reviews	yeah they are cambered factory. Thanks a lot bro. Helped a lot.

03-05-2011, 07:21 PM	#9
towlie Nissanaholic! Join Date: Jun 2009 Location: Pacific NorthWest Posts: 2,350 Trader Rating: (10) Feedback Score: 10 reviews	Stock fenders, roll no pull. No spacer. S13 17x9.5 +15 Fits alright lol. Battles are very stock fender friendly

03-05-2011, 08:26 PM	#10
upsdude Premium Member Join Date: Apr 2009 Location: Fontana (the good part) Posts: 2,684 Trader Rating: (46) Rides Gallery: upsdude Feedback Score: 46 reviews	i had 245/40/17's on my old bronze battles(17x9.5 +15) and had poke like a mother lol...they stuck out like 3/4" to 1"

Sponsored Links