Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk

Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 05-23-2012, 11:58 AM   #31
RandallSharp
Zilvia Member
 
RandallSharp's Avatar
 
Join Date: Oct 2011
Location: Ohio
Age: 25
Posts: 183
Trader Rating: (0)
RandallSharp is an unknown quantity at this point
Feedback Score: 0 reviews
Awesome! Glad this popped up. I need to rebuild my 240 calipers! I figure the procedure is very similar?
__________________
1991 240sx Hatch Daily'd!
RandallSharp is offline   Reply With Quote
Sponsored Links
Old 05-23-2012, 12:07 PM   #32
Briou
Zilvia Member
 
Briou's Avatar
 
Join Date: Jun 2011
Location: Bay St. Louis, MS
Age: 25
Posts: 182
Trader Rating: (3)
Briou is an unknown quantity at this point
Feedback Score: 3 reviews
If I had to guess I would think it would be similar...
Briou is offline   Reply With Quote
Old 06-09-2012, 09:52 PM   #33
Dorifto Machine
Zilvia Junkie
 
Dorifto Machine's Avatar
 
Join Date: May 2011
Location: Orlando Fl.
Posts: 496
Trader Rating: (17)
Dorifto Machine is an unknown quantity at this point
Feedback Score: 17 reviews
Thumbs up

Nice Job on getting the rebuild done.

I suggest to anyone who doesn't have a compressor to not use any tool within the inner walls of the pistons. If you can get the tool on the outside of the piston and pull it out then that will save you from damaging the walls of the pistons..

I found through trial an error the best way to pull the pistons out without a compressor is using the following tools and method:
A long flat head screw driver and or small crowbar, cardboard, and 1 C-clamp (4 in or bigger).
You will need a table of some sort to lay the caliper half on and you will then C-clamp the caliper half to the table ( this way the caliper will not move at all). The pistons should be facing down towards the table.
Use the cardboard on the clamp side that goes to caliper so it doesn't scratch or damage your paint or the caliper itself. You then take a flat head screw driver or small crowbar and put it on the lip of the piston (using the caliper for torque) you push down and the piston will slide out. If it does not slide out or gives your trouble, you can push down 1 side of the piston at a time and you will be able to slowly shimmy it out.

The screws can be torqued to 60 pounds.

If you don't have grease you can use brake fluid to lube the pistons / seals when you push them back in.

The stages of my rebuild:
Dorifto Machine is offline   Reply With Quote
Old 06-19-2016, 03:02 PM   #34
Nissan2nr22
Premium Member
 
Nissan2nr22's Avatar
 
Join Date: Aug 2008
Location: USA
Posts: 1,366
Trader Rating: (28)
Nissan2nr22 is an unknown quantity at this point
Feedback Score: 28 reviews
Hello i was wondering if the bad assembly clips are 100% necessary?

Not the ring and top spring, the clips that go on the back of the pads and meets the pistons
Nissan2nr22 is offline   Reply With Quote
Reply

Bookmarks

Tags
brake, rebuild, seals, z32


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 10:29 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
vB.Sponsors
Copyright © 1998 - 2015, Zilvia.net™