GWB654 Finally Complete Build(For Now) - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

GWB654 · 04-10-2011, 06:42 PM

First i would like to thank my family and friends especially my wife and Hulkster_S13. i couldn't have done it with out you! So a little background on me first. Born and raised on the island of oahu. Started karting at the age of 10, Hawaii State Karting Champion in 2001 KT100 class. Racing is in my family. My dad race’s a DB1 FF in the San Francisco region SCCA. I have been in to 240sx since 1999, drifting since 2003. Got out of the drifting scene due to the only raceway park on our island shut down(still no track due to dirty politics!!!!!). I purchased this s13 in april of 2007 for the price of a whooping $700 with a 180sx type x black top. Only running on three cylinders. compression test reveals cylinder #4 zero compression, Leak down test on #4 reveals that a intake valve stuck open. So i decide i am going to do a full rebuild. After removal of the head it is revealed that a washer had some how got in between the valve and head keeping it open. So the build began. Due to the high cost of shipping to hawaii i would wait till i had some cash to throw away in shipping before i ordered stuff. It took a long time to get all the parts. So i will let the pic’s do the talking. If you don't like it then press the back button and move along!

Mod list

Engine: E5 180sx Black top

Eagle rods
JE pistons
ARP mains
ARP rod bolts
ARP head Studs
Supertec Duel titanium Valve springs & Retainers
Rocker arm stoppers
5 angle valve job
Brian Crower 264 cams
Cosworth head gasket
New oil pump
New rear main seal
Greddy oil pan
Garrett GT3071R turbocharger with T3 .78 AR Twin Scroll
Full-Race SR ProStreet Gen 2 Manifold
Full-race 3.0in Gen 2 down-pipe
Tial 44mm Waste-gate
Aftermarket intake manifold
90mm throttle body
Yashio Factory water pump pulley
ATI super damper pulley
Spit-Fire coil packs
Synapse Synchronic BOV
Universal Intercooler with 3.0in inlet and outlet
Custom Intercooler piping

Electronics

Apex-i Power FC D-Jetro
Apex-i AVC-R
AEM Wide Band air fuel ratio
Stack ST8100 dash display
Painless 12 circuit race car wiring harness

Drivetrain

Exedy stage 2 Clutch
Stock flywheel
Stock trans
Short shifter
One piece Drive shaft
NO DIFF YET

Chassis

Tein Super Drift Coilovers
Jic tension rods
Kazama subframe collars
kazama RUCA
Kazama toe rod
Kazama traction Rod
300zx brakes front and rear
300zx rear ebrake assembly
300zx booster
300zx master cylinder
New 88 rotors all around
De powered Steering Rack(the right way)

Fuel

Sard 800cc top feed Injectors
Sard FPR
Summit 15 gal fuel cell
2 liter fuel surge tank
Summit fuel Pump (from tank to surge tank)
Bosch 044 High Pressure Fuel Pump(surge tank to fuel rail)
Custom 3/8 fuel lines from back to front of car
2 in-line fuel filters

Interior

Corbeau FX1 seats
Nagisa side mount ultra low seat rails
Sparco removable Steering Wheel hub
NRG suede steering wheel
Schroth Racing 6 point Profi II harness
Custom roll cage(Changed a few times)
Grex shift knob

Exterior

Origin Agresive style kit
Kouki wing
Unknown roof wing
Unknown hood
Seibon carbon hatch
Fenders made by my friend hulkster_s13
Weds Kranze Rapier
fronts- 19x10 +13 235/35
rears- 19x12 -3 275/30
Parts shop max spacers all around

i think that is it but i am probably missing something! thanks for taking the time to check out my build thread.

GWB654 · 04-10-2011, 06:45 PM

more pics hope you enjoy!

wannabdr1ftr · 04-10-2011, 06:46 PM

Insane! 19s...wow. Can't wait to see more.

holemilk00 · 04-10-2011, 06:49 PM

Damn it looks nice man.

Just one question, it doesn't look like you got much penetration on that stitch welding, got any better pics and what settings and gas and such were you using?

worr20 · 04-10-2011, 07:09 PM

Best car to come out of oahu. CHEEE 808allday!!!

Have you thought about Notching the frame thats right above the front wheels? Itd give you way more room for them dubs to move around and not rub up there

240sxdriftin · 04-10-2011, 07:16 PM

at first i was like whoa bro.. your roof wing is the wrong spot... then it was fixed.. hahahaha dope build!

heavenboundkevin · 04-10-2011, 07:18 PM

are spam musubi's at 7-11 still .79 cents? nice car.

yomisiu · 04-10-2011, 07:28 PM

wowowowoowoww

JDMJNKY · 04-10-2011, 07:31 PM

I'm such a fan of this car! Bump for u!

Bubba · 04-10-2011, 07:49 PM

That is definitely a sick car. +1 is such an understatement.

worr20 · 04-10-2011, 08:00 PM

Quote:

Originally Posted by heavenboundkevin

are spam musubi's at 7-11 still .79 cents? nice car.

1.25

1.50 for da kine special wit egg

I think. I left in November. maybe it changed.

GWB654 · 04-10-2011, 09:55 PM

Quote:

Originally Posted by worr20

1.25

1.50 for da kine special wit egg

I think. I left in November. maybe it changed.

yup 1.25 is the going rate for spam musubi and we can still get spam eggs and rice from the Mcdonalds drive thru. i for got to say that all work was done by me and hulkster_s13. all machine work was done at Snyders in waipahu, tune was and is going to be done by sean at Munky Wurks Garage. thanks for all the comments!

s14tan · 04-10-2011, 10:19 PM

Those rear quarters look sick!!! Did you say they were custom?

Nick_04K · 04-10-2011, 10:29 PM

Damn this thing is aggressive! 19's on an s13 is straight up crazy. How much travel do you think the front has before the tires hit the chassis?

ZilviaKid · 04-10-2011, 10:58 PM

Quote:

Originally Posted by s14tan

Those rear quarters look sick!!! Did you say they were custom?

they look identical to kougouchi power to me

hulkster_s13 · 04-10-2011, 11:15 PM

they are almost identical, subtle differences, i didnt want to make exact replicas

satek · 04-10-2011, 11:57 PM

Very impressive....those 19s look massive!!

jdizzy204 · 04-11-2011, 12:04 AM

i like everything except the wheels.the exterior color is bi-winning!!

sqd · 04-11-2011, 12:48 AM

That is awesome! Love it.

Om1kron · 04-11-2011, 01:11 AM

do you have the covers to those kranze rapiers?

GWB654 · 04-11-2011, 01:17 AM

Quote:

Originally Posted by Om1kron

do you have the covers to those kranze rapiers?

I do just got to get lug nuts that fit under them.

worr20 · 04-11-2011, 05:47 AM

Im glad those wheels stayed in with someone thatll use em good. lets see some sampo vids at firestations. lol

Id love to see this car being used. Im coming back in may to get married im pretty excited to see the aina again. wahiawa born and raised! where you from? Looks like kaneohe/kailua side.

Anyway Great job with the car! even though itd look more crazy with the front low. but being 19s i doubt thats possible without notching.

shoots

ruthlessef-9 · 04-11-2011, 06:18 AM

Mean!!! 808 represent

blueshark123 · 04-11-2011, 09:10 AM

Sick car, thumbs up but i would change the rims they are to vip for this car or atleast get them painted

GWB654 · 04-11-2011, 09:32 AM

Quote:

Originally Posted by worr20

Im glad those wheels stayed in with someone thatll use em good. lets see some sampo vids at firestations. lol

Id love to see this car being used. Im coming back in may to get married im pretty excited to see the aina again. wahiawa born and raised! where you from? Looks like kaneohe/kailua side.

Anyway Great job with the car! even though itd look more crazy with the front low. but being 19s i doubt thats possible without notching.

shoots

If I could score a safety check that could happen but chances of recon are slim so we will see if it ever will get street legal

Quote:

Originally Posted by blueshark123

Sick car, thumbs up but i would change the rims they are to vip for this car or atleast get them painted

I have been debating painting them for awile now but havent made up my mind!

AE_Racer · 04-11-2011, 09:39 PM

Not a fan of the wheel setup but very quality build. Thanks for sharing!

X2daC · 04-11-2011, 10:36 PM

That car is ridiculous.

Needs less Corbeau though.

iROCKchucks · 04-11-2011, 11:34 PM

I see how u put a stop to the pink theme, and just left it under the hood..thought it was going down hill for a sec. Nice build.

97240TB · 04-12-2011, 03:09 AM

Love everything Except the pink, The front wheels are too big honestly. Car would look great if it were lower.

PoorMans180SX · 04-12-2011, 07:37 AM

This is cool man! You've got your own style, but you still have good taste. That is a rare combo my friend.

04-10-2011, 06:42 PM	#1
GWB654 Leaky Injector Join Date: Mar 2007 Location: hawaii Posts: 97 Trader Rating: (1) Feedback Score: 1 reviews	GWB654 Finally Complete Build(For Now) First i would like to thank my family and friends especially my wife and Hulkster_S13. i couldn't have done it with out you! So a little background on me first. Born and raised on the island of oahu. Started karting at the age of 10, Hawaii State Karting Champion in 2001 KT100 class. Racing is in my family. My dad race’s a DB1 FF in the San Francisco region SCCA. I have been in to 240sx since 1999, drifting since 2003. Got out of the drifting scene due to the only raceway park on our island shut down(still no track due to dirty politics!!!!!). I purchased this s13 in april of 2007 for the price of a whooping $700 with a 180sx type x black top. Only running on three cylinders. compression test reveals cylinder #4 zero compression, Leak down test on #4 reveals that a intake valve stuck open. So i decide i am going to do a full rebuild. After removal of the head it is revealed that a washer had some how got in between the valve and head keeping it open. So the build began. Due to the high cost of shipping to hawaii i would wait till i had some cash to throw away in shipping before i ordered stuff. It took a long time to get all the parts. So i will let the pic’s do the talking. If you don't like it then press the back button and move along! Mod list Engine: E5 180sx Black top Eagle rods JE pistons ARP mains ARP rod bolts ARP head Studs Supertec Duel titanium Valve springs & Retainers Rocker arm stoppers 5 angle valve job Brian Crower 264 cams Cosworth head gasket New oil pump New rear main seal Greddy oil pan Garrett GT3071R turbocharger with T3 .78 AR Twin Scroll Full-Race SR ProStreet Gen 2 Manifold Full-race 3.0in Gen 2 down-pipe Tial 44mm Waste-gate Aftermarket intake manifold 90mm throttle body Yashio Factory water pump pulley ATI super damper pulley Spit-Fire coil packs Synapse Synchronic BOV Universal Intercooler with 3.0in inlet and outlet Custom Intercooler piping Electronics Apex-i Power FC D-Jetro Apex-i AVC-R AEM Wide Band air fuel ratio Stack ST8100 dash display Painless 12 circuit race car wiring harness Drivetrain Exedy stage 2 Clutch Stock flywheel Stock trans Short shifter One piece Drive shaft NO DIFF YET Chassis Tein Super Drift Coilovers Jic tension rods Kazama subframe collars kazama RUCA Kazama toe rod Kazama traction Rod 300zx brakes front and rear 300zx rear ebrake assembly 300zx booster 300zx master cylinder New 88 rotors all around De powered Steering Rack(the right way) Fuel Sard 800cc top feed Injectors Sard FPR Summit 15 gal fuel cell 2 liter fuel surge tank Summit fuel Pump (from tank to surge tank) Bosch 044 High Pressure Fuel Pump(surge tank to fuel rail) Custom 3/8 fuel lines from back to front of car 2 in-line fuel filters Interior Corbeau FX1 seats Nagisa side mount ultra low seat rails Sparco removable Steering Wheel hub NRG suede steering wheel Schroth Racing 6 point Profi II harness Custom roll cage(Changed a few times) Grex shift knob Exterior Origin Agresive style kit Kouki wing Unknown roof wing Unknown hood Seibon carbon hatch Fenders made by my friend hulkster_s13 Weds Kranze Rapier fronts- 19x10 +13 235/35 rears- 19x12 -3 275/30 Parts shop max spacers all around i think that is it but i am probably missing something! thanks for taking the time to check out my build thread. __________________ STOP DREAMING AND START DRIFTING

04-10-2011, 06:45 PM	#2
GWB654 Leaky Injector Join Date: Mar 2007 Location: hawaii Posts: 97 Trader Rating: (1) Feedback Score: 1 reviews	more pics hope you enjoy! __________________ STOP DREAMING AND START DRIFTING

04-10-2011, 06:46 PM	#3
wannabdr1ftr Zilvia Junkie Join Date: Jan 2009 Location: TX Age: 37 Posts: 551 Trader Rating: (0) Feedback Score: 0 reviews	Insane! 19s...wow. Can't wait to see more. __________________

04-10-2011, 07:16 PM	#6
240sxdriftin Zilvia FREAK! Join Date: Sep 2005 Location: Dayton, OH Age: 35 Posts: 1,377 Trader Rating: (25) Feedback Score: 25 reviews	at first i was like whoa bro.. your roof wing is the wrong spot... then it was fixed.. hahahaha dope build! __________________ IG: @bwagg88

04-10-2011, 07:31 PM	#9
JDMJNKY Zilvia Addict Join Date: Aug 2008 Location: sOuL-CaL Age: 41 Posts: 774 Trader Rating: (11) Feedback Score: 11 reviews	I'm such a fan of this car! Bump for u! __________________ Facebook.com/NiteGrind

04-10-2011, 06:49 PM	#4
holemilk00 Nissanaholic! Join Date: Oct 2006 Location: Cape Coral, FL Posts: 2,485 Trader Rating: (33) Feedback Score: 33 reviews	Damn it looks nice man. Just one question, it doesn't look like you got much penetration on that stitch welding, got any better pics and what settings and gas and such were you using? __________________ I had a cool signature

04-10-2011, 07:09 PM	#5
worr20 Zilvia Member Join Date: Jan 2007 Location: Hawaii/W.V. Posts: 153 Trader Rating: (1) Feedback Score: 1 reviews	Best car to come out of oahu. CHEEE 808allday!!! Have you thought about Notching the frame thats right above the front wheels? Itd give you way more room for them dubs to move around and not rub up there

04-10-2011, 07:28 PM	#8
yomisiu Nissanaholic! Join Date: Oct 2010 Location: St. Pete, FL Posts: 1,675 Trader Rating: (16) Feedback Score: 16 reviews	wowowowoowoww

04-10-2011, 07:49 PM	#10
Bubba Zilvia Junkie Join Date: Feb 2006 Location: Biloxi, MS Age: 40 Posts: 352 Trader Rating: (2) Feedback Score: 2 reviews	That is definitely a sick car. +1 is such an understatement. __________________ Good at wrenching, terrible at electrical. Lord help me... HAHAHA

04-10-2011, 10:19 PM	#13
s14tan Zilvia Junkie Join Date: Sep 2007 Location: Dallas.Texas Age: 34 Posts: 582 Trader Rating: (8) Feedback Score: 8 reviews	Those rear quarters look sick!!! Did you say they were custom? __________________

04-10-2011, 10:29 PM	#14
Nick_04K Zilvia Junkie Join Date: Jun 2010 Location: Vernal, UT Age: 29 Posts: 467 Trader Rating: (0) Feedback Score: 0 reviews	Damn this thing is aggressive! 19's on an s13 is straight up crazy. How much travel do you think the front has before the tires hit the chassis?

04-10-2011, 11:15 PM	#16
hulkster_s13 Zilvia Member Join Date: Nov 2005 Location: down by da beach Posts: 276 Trader Rating: (9) Feedback Score: 9 reviews	they are almost identical, subtle differences, i didnt want to make exact replicas

04-10-2011, 11:57 PM	#17
satek Leaky Injector Join Date: Jan 2010 Location: Vancouver BC Age: 33 Posts: 132 Trader Rating: (0) Feedback Score: 0 reviews	Very impressive....those 19s look massive!!

04-11-2011, 12:04 AM	#18
jdizzy204 Zilvia FREAK! Join Date: Oct 2004 Location: berlin Age: 36 Posts: 1,041 Trader Rating: (11) Feedback Score: 11 reviews	i like everything except the wheels.the exterior color is bi-winning!!

04-11-2011, 12:48 AM	#19
sqd Leaky Injector Join Date: Sep 2009 Location: Sweden Age: 37 Posts: 104 Trader Rating: (0) Feedback Score: 0 reviews	That is awesome! Love it.

04-11-2011, 01:11 AM	#20
Om1kron Post Whore! Join Date: Sep 2004 Location: Granada Hills, CA Age: 43 Posts: 6,990 Trader Rating: (15) Feedback Score: 15 reviews	do you have the covers to those kranze rapiers? __________________ Wayne Edwards https://om1kron.blogspot.com

04-11-2011, 05:47 AM	#22
worr20 Zilvia Member Join Date: Jan 2007 Location: Hawaii/W.V. Posts: 153 Trader Rating: (1) Feedback Score: 1 reviews	Im glad those wheels stayed in with someone thatll use em good. lets see some sampo vids at firestations. lol Id love to see this car being used. Im coming back in may to get married im pretty excited to see the aina again. wahiawa born and raised! where you from? Looks like kaneohe/kailua side. Anyway Great job with the car! even though itd look more crazy with the front low. but being 19s i doubt thats possible without notching. shoots

04-11-2011, 06:18 AM	#23
ruthlessef-9 Join Date: Jul 2009 Location: Oahu, Hawaii Age: 41 Posts: 48 Trader Rating: (0) Feedback Score: 0 reviews	Mean!!! 808 represent

04-11-2011, 09:10 AM	#24
blueshark123 Post Whore! Join Date: Apr 2006 Location: North Jersey Posts: 5,481 Trader Rating: (55) Feedback Score: 55 reviews	Sick car, thumbs up but i would change the rims they are to vip for this car or atleast get them painted

04-11-2011, 09:39 PM	#26
AE_Racer Zilvia Addict Join Date: Feb 2005 Location: Lost in the woods of FAILorida Age: 36 Posts: 777 Trader Rating: (9) Feedback Score: 9 reviews	Not a fan of the wheel setup but very quality build. Thanks for sharing! __________________ http://tougestars.net

04-11-2011, 10:36 PM	#27
X2daC Leaky Injector Join Date: Feb 2009 Location: Florida Age: 38 Posts: 51 Trader Rating: (0) Feedback Score: 0 reviews	That car is ridiculous. Needs less Corbeau though. __________________ Looking for an S14/S13 Project. All you need to know.

04-11-2011, 11:34 PM	#28
iROCKchucks Leaky Injector Join Date: Aug 2009 Location: Arlington, TX Posts: 114 Trader Rating: (0) Feedback Score: 0 reviews	I see how u put a stop to the pink theme, and just left it under the hood..thought it was going down hill for a sec. Nice build.

04-12-2011, 03:09 AM	#29
97240TB Zilvia Junkie Join Date: Oct 2009 Location: Tampa, Florida Age: 36 Posts: 338 Trader Rating: (0) Feedback Score: 0 reviews	Love everything Except the pink, The front wheels are too big honestly. Car would look great if it were lower. __________________ 97' 240SX, VQHR swap Combplete.

04-12-2011, 07:37 AM	#30
PoorMans180SX Zilvia.net Advertiser Join Date: Nov 2005 Location: Michigan Age: 36 Posts: 5,573 Trader Rating: (16) Rides Gallery: PoorMans180SX Feedback Score: 16 reviews	This is cool man! You've got your own style, but you still have good taste. That is a rare combo my friend. __________________ Build: http://zilvia.net/f/showthread.php?t=643065 Friends don't let friends buy knock-offs.