CA Drift Freaq Polyurethane Engine & Trans Mounts! FINAL CLEARANCE SALE!

[drift freaq]

Originally Posted by elucid

do your new green engine mounts still adjust height by spinning them?

The studs are centered now and set the engine at the ideal position. I had customers trying to raise their engines when they were adjustable. The problem was I made them adjustable so people could lower the engine as a lower center of gravity is better. But..... These guys had their cars way to slammed and were afraid of scraping their oil pans. When you raise the engine it puts the mount at a severely leveraged angle which is not good for the mount and could cause failure.

The easiest way to correct the issue was what I did with the new design. They still work great and people love them.

[SeizureNoodles]

Are these mounts taller than the KA mounts? I just checked my RB20 and these mounts are about half an inch taller... :\

[drift freaq]

Originally Posted by SeizureNoodles

Are these mounts taller than the KA mounts? I just checked my RB20 and these mounts are about half an inch taller... :\

No they are not taller than KA mounts. If your KA mounts were old though they would most likely be sagging as the rubber does that when it gets old. The Nismo mounts are the same height as stock new KA mounts and my mounts are a 1/2 inch shorter.

[elucid]

Originally Posted by drift freaq

The studs are centered now and set the engine at the ideal position. I had customers trying to raise their engines when they were adjustable. The problem was I made them adjustable so people could lower the engine as a lower center of gravity is better. But..... These guys had their cars way to slammed and were afraid of scraping their oil pans. When you raise the engine it puts the mount at a severely leveraged angle which is not good for the mount and could cause failure.

The easiest way to correct the issue was what I did with the new design. They still work great and people love them.

I see, if you have the older style mounts with the offset bolts i will take a set, i need to lower the engine.

[drift freaq]

Originally Posted by elucid

I see, if you have the older style mounts with the offset bolts i will take a set, i need to lower the engine.

The mounts currently set your at the ideal position which is the lowest that the offset mounts did.

[sean2000gt]

Sent you a pm!

[drift freaq]

Originally Posted by sean2000gt

Sent you a pm!

Got it man.

[williamb]

Just ordered engine mounts

[drift freaq]

Originally Posted by williamb

Just ordered engine mounts

Got it and they have been shipped.

[status_ryan]

Just sent payment for full set. Super pumped!!

[drift freaq]

Originally Posted by status_ryan

Just sent payment for full set. Super pumped!!

Got it and it's been shipped.

[zombiewolf513]

Got these mounts. Love em.

[drift freaq]

sale is over.

[drift freaq]

Originally Posted by elucid

I see, if you have the older style mounts with the offset bolts i will take a set, i need to lower the engine.

I need to clarify this. The current engine mounts are only a possible 1/4 inch different in height to the old offset ones. It's really not enough to make any difference.

If you are having hood cleanse issues due to bad knock off aftermarket vented hoods you should not have bought those hoods.


I should add that that depending on the the engine you are running the trans mount may cause some minor vibrations due to it being much stiffer than the stock trans mount which was purposely made wimpy by Nissan to cut down on vibration. Any aftermarket trans mount is going to cause a bit of vibration if it is actually a real upgraded mount. These mounts also have to take time to set in, after that the vibration diminishes.

Nismo trans mounts are really not an upgrade but actually just a stock replacement. You will not yield the benefits of an actual aftermarket upgraded one.[/SIZE]

[drift freaq]

I am going to extend this out a few more days for those that did not see it yet.

[jame5x]

Payment just sent!

[SeizureNoodles]

Just wanted to update that these mounts are legit. The engine mounts didn't fit my RB with R32 crossmember, but that wasn't advertised, just me not quadruple checking that they would fit. The Trans mount is amazing though, I test drove my car today and was able to shift easily without a shift nob. Try it sometime with your current mounts and I can almost guarantee it will be a bitch.

[drift freaq]

Thanks for the props. Keep those orders coming people the sale will run till the end of the week.

[gnozahs]

Tranny mounts are great. Installed and shifter doesn't move around or jump up and down on freeway anymore like it used to.

[drift freaq]

Originally Posted by gnozahs

Tranny mounts are great. Installed and shifter doesn't move around or jump up and down on freeway anymore like it used to.

See now like I have stated for the people who spoken up about vibration . If it really was that bad people would not be making posts like above. You get a slight vibration at idle with some engines because it's very solid but what is written above is the excellent tradeoff you get.

[drift freaq]

This sale will end tomorrow people.

[jame5x]

Got mine today. Thanks for the Von's ad, I needed eggs.

[drift freaq]

Originally Posted by jame5x

Got mine today. Thanks for the Von's ad, I needed eggs.

Hahahaha glad to help.

[driftheart]

Hey drift freaq, how much for the tranny mount and a motor mount shield shipped to 07503?

[drift freaq]

Originally Posted by driftheart

Hey drift freaq, how much for the tranny mount and a motor mount shield shipped to 07503?

That would be $259 shipped

[Yad]

How much for the motor mounts with heatshield for a ka24de shipped down to 00909 thank in advance

[drift freaq]

Originally Posted by Yad

How much for the motor mounts with heatshield for a ka24de shipped down to 00909 thank in advance

$151 shipped because I use priority mail.

[Yad]

Payment sent i cant wait to have these bad boys installed

[jame5x]

I'm still looking for a shop that'll install these. Can't seem to find a shop that charges less than $200. I was looking at them this morning and my motor mounts have these on the thread. I tried to hand tightening the nut to see if I can thread the excess out but was kind of hard so I stopped. Is this normal?



Sorry, not sure how to resize the pic.

[drift freaq]

That is just excess, it will clean out of the threads when you tighten down the nut.