Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk

Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 06-30-2005, 11:25 PM   #1
sil80SR
 
sil80SR's Avatar
 
Join Date: Jun 2005
Location: Charlotte, NC
Age: 37
Posts: 2
Trader Rating: (0)
sil80SR is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to sil80SR
How do i wire a KA24E MAF in a SR20DET?

hey, i need your help guys.
i searched, but no one ever explaid how to wire the sohc ka maf in a sr20det maf harness.


i got a s13 sr20det and i am replacing the maf.

what i got:
the MAF harness has a thick black wire with a red stripe, a normal black wire, and a white one

looks like i got a sr20det mafs installed but its bad. or so i was told. (4 pin plug - only 3 wires)

the sohc maf that i found is a 3 pin plug (black/white, black, and white wires coming from the plug)


i connected the maf like this:
black/white to black/red, black to black, and white to white.

it doesnt run very well. the car is chocking down on gas at 3500 rpms. feels like its going into the "safemode" and its not ingiting the air/fuel mixture, and it just stops going up after about 3500rpms.

people told me that the wires dont connect by the color code... so here is my question...

does anyone know how to wire the SOHC MAF onto a SR20DET Maf harness. ?
sil80SR is offline   Reply With Quote
Sponsored Links
Old 07-01-2005, 09:22 AM   #2
nismo101
 
Join Date: Dec 2002
Posts: 23
Trader Rating: (0)
nismo101 is an unknown quantity at this point
Feedback Score: 0 reviews
I believe it is not running correctly because you cannot use a KA MAF on an SR.
They are calibrated differently.

If I am wrong and people have got a KA maf to work on an SR, then I would say swap a few wires until it runs right.
__________________
Aaron S.
Portland, OR
1972 Datsun 510 w/SR20DET
1997 240sx
nismo101 is offline   Reply With Quote
Old 07-01-2005, 09:32 AM   #3
caall99
Zilvia Member
 
caall99's Avatar
 
Join Date: Apr 2005
Location: Wellesley, MA
Age: 39
Posts: 267
Trader Rating: (0)
caall99 is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to caall99
i am using a ka24e MAF, and i believe i wired it in correctly. my car also hesitates/stumbles/bogs while i accelerate. in neutral i can rev the engine all the way to redline without any hesitation, its only when i drive the car that i get this stumbling randomly throughout the rev range. maybe its related to the car building boost...
__________________
Signature over limits
http://www.zilvia.net/f/showthread.php?t=21036
caall99 is offline   Reply With Quote
Old 07-01-2005, 12:36 PM   #4
sil80SR
 
sil80SR's Avatar
 
Join Date: Jun 2005
Location: Charlotte, NC
Age: 37
Posts: 2
Trader Rating: (0)
sil80SR is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to sil80SR
yes. thats exactly my problem. in neutral the car revs up all the way, in gear, it chokes down at about 3500 or if the turbo is boosting up.

i was told that the ka24e maf wires do not connect to the sr20det harness by color. its different. thats what i am trying to figure out.

well everybody knows that the ka24e mafs only can hold up to 12 psi's or boost.

but i need it on my car until i install my safc and my 300zx maf
sil80SR is offline   Reply With Quote
Old 07-06-2005, 02:28 PM   #5
BayS13
Zilvia Junkie
 
Join Date: Feb 2005
Location: Bay Area/ Osaka
Posts: 536
Trader Rating: (4)
BayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really niceBayS13 is just really nice
Feedback Score: 4 reviews
anyone got a FAQ on this or something? i need to do this on my car
BayS13 is offline   Reply With Quote
Old 07-06-2005, 04:24 PM   #6
caall99
Zilvia Member
 
caall99's Avatar
 
Join Date: Apr 2005
Location: Wellesley, MA
Age: 39
Posts: 267
Trader Rating: (0)
caall99 is an unknown quantity at this point
Feedback Score: 0 reviews
Send a message via AIM to caall99
i am def bumping this shit, it might lead to some good info... plus i am still having this same problem...
__________________
Signature over limits
http://www.zilvia.net/f/showthread.php?t=21036
caall99 is offline   Reply With Quote
Old 07-06-2005, 09:36 PM   #7
sdtouge
BANNED
 
Join Date: Dec 2004
Location: san diego
Posts: 479
Trader Rating: (0)
sdtouge can only hope to improve
Feedback Score: 0 reviews
KA24E --> CA/SR
black --> black
black/white --> black/white
White --> Green/black
***Green/yellow don't connect

i recomend usinmg shielded wire to extend/splice this.
also its really easy to do
matt
sdtouge is offline   Reply With Quote
Old 05-25-2006, 04:06 PM   #8
GSXRJJordan
Post Whore!
 
GSXRJJordan's Avatar
 
Join Date: May 2006
Location: San Diego, CA
Posts: 9,135
Trader Rating: (19)
GSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfectionGSXRJJordan is close to perfection
Feedback Score: 19 reviews
Send a message via AIM to GSXRJJordan
bump for some of my guys who have this setup ~ problem is, we didn't have the wires coming off his KA24E SOHC MAFS... just the A/B/C pin spot. I wired it up like so:

KA24E -> Red Top SR20DET Harness
A -> Black/White (+12V)
B -> Black (GND)
C -> White (Signal)

I'm not positive about the function of each wire off the top of my head (might be Signal, GND, +12V, but I remember something being fishy with the colors... anyway...)

All the SR swaps we do here at Milano Motorsports leave the shop with a KA24E MAFS, unless the customer wants to do fuel management right off the bat. Definitely not a bad way to go, especially 'cause I can count the number of SR20's I've seen from Japan that have MAFS' on em with one thumb...
__________________


Jordan Innovations has a new web site!
www.JordanInnovations.com -- All your favorite FD Pro Drifters love it, trust me -- www.JordanInnovations.com
GSXRJJordan is offline   Reply With Quote
Old 08-04-2006, 10:08 AM   #9
delphis
Zilvia Junkie
 
Join Date: Aug 2006
Location: antioch
Age: 41
Posts: 312
Trader Rating: (0)
delphis has a spectacular aura aboutdelphis has a spectacular aura aboutdelphis has a spectacular aura aboutdelphis has a spectacular aura aboutdelphis has a spectacular aura aboutdelphis has a spectacular aura about
Feedback Score: 0 reviews
anyone have any idea if the sr20de is the same setup as the sr20det on the wiring?
delphis is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 09:25 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net