|
Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars |
|
Thread Tools | Display Modes |
01-17-2012, 09:23 PM | #61 |
Hey guys so i have been trying to smog my 91 240 (dohc)
it passed everything except the nox(common thing with 240s) so i cleaned the egr valve and the metal pipe that goes around form the exhaust manifold to the air manifold. My nox was reading 3300. and i was wondering if that's possible, perhaps i hooked the egr back on wrong? can some one please help me :/ |
|
Sponsored Links |
01-19-2012, 03:45 PM | #63 |
Post Whore!
Join Date: Jan 2008
Location: LAND of the LOST
Posts: 4,083
Trader Rating: (92)
Feedback Score: 92 reviews
|
Damn smog gremlins chasing me again..
15 mph HC 61/64 FAIL BY 3 CO 0.52/0.07 NO 493/847 FAIL WTF 25 mph HC 47/41 CO 0.50/0.05 NO 516/952 FAIL WTF I replaced my egr 2 years ago along with the egr solenoid and the egr BPT .. I cleaned the passage way to the egr via the 10mm hex bolt sea foam the engine except running it crank case I only did gas and intake ??? What else should I do??? |
01-20-2012, 01:49 AM | #65 |
Zilvia Junkie
Join Date: Apr 2008
Location: san bernardino
Posts: 375
Trader Rating: (1)
Feedback Score: 1 reviews
|
is the timing right? what was the CO2 at?
__________________
https://www.linkedin.com/in/hassanbakar |
01-20-2012, 03:01 AM | #66 |
Leaky Injector
Join Date: Jun 2011
Location: Seattle, Wa
Age: 33
Posts: 102
Trader Rating: (1)
Feedback Score: 1 reviews
|
get a little under half a tank of gas in your car, then put in like half a gallon of denatured alcohol in the tank, and take smog again.
Makes your shit CLEAN but then as soon as you leave, go fill up your tank and drive nicely |
01-20-2012, 04:27 PM | #70 | |
Zilvia Addict
Join Date: Sep 2009
Location: Nor Cal
Age: 37
Posts: 720
Trader Rating: (10)
Feedback Score: 10 reviews
|
Quote:
taken from another forum \/ Seafoam ( Pros and Cons) : General Chat |
|
01-21-2012, 10:45 AM | #71 |
Post Whore!
Join Date: Jan 2008
Location: LAND of the LOST
Posts: 4,083
Trader Rating: (92)
Feedback Score: 92 reviews
|
Since my hc were off by 3 and only on low speed..is it safe to say that my ignition system is good enough..just a little more cleaning ...and since my co where hella low is it safe to say my cat is ok ??? Nox I know primarily has to deal with egr..so I'm assuming I have a clogged egr pipe..bc if my egr was to be completely broken my nox would be at a stupid level ..
|
01-21-2012, 05:49 PM | #73 |
Post Whore!
Join Date: Jan 2008
Location: LAND of the LOST
Posts: 4,083
Trader Rating: (92)
Feedback Score: 92 reviews
|
Checked egr function there is a vacuum source, and the egr valve does move while at 2000 rpm and closes at idle...slapped a brand new o2 sensor just for the hell of it..my question is is it vital or should i just do it ..that I clean out the egr tube to the exhaust manifold?
Last edited by S-Nation S13; 01-21-2012 at 08:30 PM.. |
01-21-2012, 10:33 PM | #74 |
I just passed my emissions today. my problem was my egr wasn't on completely,clean your pipe with wd40 and your valve. I put 5 gallons of 91 oct. and alcohol set my timing all the way to lean. Passed flying colors. and my nox before was reading 3300.
|
|
01-22-2012, 02:05 PM | #76 |
Post Whore!
Join Date: Jan 2008
Location: LAND of the LOST
Posts: 4,083
Trader Rating: (92)
Feedback Score: 92 reviews
|
Able to remove the egr with the egr tube today..my plan is to spray into the egr tube with carb cleaner..and into the holes they hook up to.. Can I spray into the egr as well ?? My egr is in working condition , that means the egr bpt and egr solenoid is working as well..so I'm thinking a good clean will lower my nox..
Any other tips or cleaning I should do please lemme know .. |
01-25-2012, 12:27 PM | #78 |
My no ppm was 3346 (15mph) and 2948 ppm (25mph)
i cleaned my egr valve and bpt, set timing all the way to lean. 91 oct + alcohol. made sure all the vacuum lines where sealed for the egr. passed with 0008 ppm on (15mph) 0004 ppm (25mph). |
|
04-22-2012, 12:43 AM | #80 |
Philosopher King
|
So I just attempted this and FUCK THAT PLUG. Why the fuck is there an aluminum plug in an aluminum manifold? Now I have to drill it out and get a huge extractor in there and hope the threads survive. At least the plug is like $3 and Nissan still stocks it.
__________________
G O L D E N B E A R R E P U B L I C |
07-03-2012, 02:01 PM | #81 |
Philosopher King
|
Nox at 3000+ HC slightly high @15mph
Nox around 1200 HC fine @25mph No cel. EGR works. Cat and o2 sensor replaced. Vacuum lines all new. Passage behind plug cleaned.
__________________
G O L D E N B E A R R E P U B L I C |
07-12-2012, 06:25 PM | #84 |
Join Date: Aug 2010
Location: Santa rosa, CA
Age: 35
Posts: 5
Trader Rating: (0)
Feedback Score: 0 reviews
|
hey i know this is an old post but its exactly what need to try and i was hoping you might still have the pics and be able to reset them or just send them too me it would be much appreciated!!!!! thanks!
|
Bookmarks |
|
|