Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 08-18-2013, 12:24 PM   #1
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Dipstick issues

So my dipstick keeps shootin oil out at high rpms , i just installed a new pcv my old one was black n filled wit oil tar . Took car for test run n dipstick still shoots oil at high rpm . The o ring on my dipstick is doodoo lol smh ; so maybe that the problem ? ; but my car still feels like it is hesitating when it spools .

Suggestions pleaseee , Thank You in advanced .
Itzgunzduh is offline   Reply With Quote
Sponsored Links
Old 08-18-2013, 12:30 PM   #2
SuperSR
 
Join Date: Aug 2013
Location: Panama City, FL
Posts: 6
Trader Rating: (0)
SuperSR is an unknown quantity at this point
Feedback Score: 0 reviews
Sounds like you are building up to much pressure in your crankcase. I would check the compression and perform a leakdown test to see if you have an excessive amount of blowby.
SuperSR is offline   Reply With Quote
Old 08-18-2013, 12:33 PM   #3
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by SuperSR View Post
Sounds like you are building up to much pressure in your crankcase. I would check the compression and perform a leakdown test to see if you have an excessive amount of blowby.
How would i do that ?
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 12:40 PM   #4
jr_ss
Post Whore!
 
Join Date: Dec 2005
Location: Pa
Posts: 6,410
Trader Rating: (35)
jr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond reputejr_ss has a reputation beyond repute
Feedback Score: 35 reviews
Send a message via AIM to jr_ss
With google... Do some research, no one is going to hold your hand.
__________________
*My SR20VET* Does your VTC gear rattle in your S14/15 SR? PM me.
jr_ss is offline   Reply With Quote
Old 08-18-2013, 12:41 PM   #5
Rich260z
Zilvia Addict
 
Join Date: Apr 2011
Location: Burbank, CA
Posts: 621
Trader Rating: (8)
Rich260z is an unknown quantity at this point
Feedback Score: 8 reviews
Let me google that for you
Rich260z is offline   Reply With Quote
Old 08-18-2013, 12:41 PM   #6
SuperSR
 
Join Date: Aug 2013
Location: Panama City, FL
Posts: 6
Trader Rating: (0)
SuperSR is an unknown quantity at this point
Feedback Score: 0 reviews
You can check the compression with compression tester gauge which you can typically rent from Autozone.

Compression Tester Gauge | AutoZone.com

The leak down tester is similar in looks but you will need a air compressor. Instead of me typing it all out here is a link that will explain it.

Leak-down tester - Wikipedia, the free encyclopedia
SuperSR is offline   Reply With Quote
Old 08-18-2013, 12:43 PM   #7
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by jr_ss View Post
With google... Do some research, no one is going to hold your hand.
Lmao ; all i did was ask a question i already been researching obviouslly . Was seein if there was other ways of doing it ..
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 12:44 PM   #8
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by Rich260z View Post
Thanks haha
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 12:45 PM   #9
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
So if my car is causing too much blow by how would i be able to stop it ?
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 12:46 PM   #10
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
Think with your dipstick jimmy!!!!!
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 12:47 PM   #11
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
Quote:
Originally Posted by itzgunzduh View Post
so if my car is causing too much blow by how would i be able to stop it ?
rebuild....,.
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 12:53 PM   #12
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by s13mikesr20 View Post
rebuild....,.
Sheesh ; well lets just hope i dnt have to do that .
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 01:00 PM   #13
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
my sr has some blow by still made 320 horses on a s14 sr t28 just sayin
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 01:02 PM   #14
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Damn lol ; i wish i had that to the wheels ; i got maybe like 250 i juss like driftin lol
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 01:06 PM   #15
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
Quote:
Originally Posted by Itzgunzduh View Post
Damn lol ; i wish i had that to the wheels ; i got maybe like 250 i juss like driftin lol
yea how much boost r u running and did you replace pcv valve and such?
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 01:57 PM   #16
joe3180
Zilvia Junkie
 
Join Date: Aug 2005
Location: 909 california
Posts: 356
Trader Rating: (11)
joe3180 is an unknown quantity at this point
Feedback Score: 11 reviews
take it to a shop, get the leak down test done. It should tell you if you have bad rings or so. The dipstick shouldn't shoot out regardless of the o ring. The oil ring is basically there to keep crap from getting in...not to keep it from shooting out the guide.
joe3180 is offline   Reply With Quote
Old 08-18-2013, 02:03 PM   #17
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by s13mikesr20 View Post
yea how much boost r u running and did you replace pcv valve and such?
8 psi i never got boost control ; cuz this started happening , and i just replaced my pcv valve today .
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:04 PM   #18
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by joe3180 View Post
take it to a shop, get the leak down test done. It should tell you if you have bad rings or so. The dipstick shouldn't shoot out regardless of the o ring. The oil ring is basically there to keep crap from getting in...not to keep it from shooting out the guide.
How much does a lewk test cost at most shops ?
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:09 PM   #19
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
one hour of labor
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 02:10 PM   #20
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Kk ill do that thursday ; should i do both test or juss leak test
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:19 PM   #21
s13mikesr20
Nissanaholic!
 
Join Date: Sep 2011
Location: las vegas
Age: 34
Posts: 1,792
Trader Rating: (8)
s13mikesr20 is an unknown quantity at this point
Feedback Score: 8 reviews
every test while your there
s13mikesr20 is offline   Reply With Quote
Old 08-18-2013, 02:20 PM   #22
EsChassisLove
Nissanaholic!
 
EsChassisLove's Avatar
 
Join Date: Jan 2011
Location: San Diego
Age: 34
Posts: 2,090
Trader Rating: (26)
EsChassisLove is an unknown quantity at this point
Feedback Score: 26 reviews
If you know anything about SRs, you'll know that SRs have blow by. LOTS of it. Even with a PERFECT engine making 500+HP.

Is your crankcase ventilation set up properly?
__________________
IG/TikTok-ThatS14_Z06guy
EsChassisLove is offline   Reply With Quote
Old 08-18-2013, 02:21 PM   #23
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
How many test r there ..? I know mad questions my bad lol
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:27 PM   #24
EsChassisLove
Nissanaholic!
 
EsChassisLove's Avatar
 
Join Date: Jan 2011
Location: San Diego
Age: 34
Posts: 2,090
Trader Rating: (26)
EsChassisLove is an unknown quantity at this point
Feedback Score: 26 reviews
Leak down and compression.
__________________
IG/TikTok-ThatS14_Z06guy
EsChassisLove is offline   Reply With Quote
Old 08-18-2013, 02:28 PM   #25
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by EsChassisLove View Post
If you know anything about SRs, you'll know that SRs have blow by. LOTS of it. Even with a PERFECT engine making 500+HP.

Is your crankcase ventilation set up properly?
How would i know if its set up properly
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:28 PM   #26
EsChassisLove
Nissanaholic!
 
EsChassisLove's Avatar
 
Join Date: Jan 2011
Location: San Diego
Age: 34
Posts: 2,090
Trader Rating: (26)
EsChassisLove is an unknown quantity at this point
Feedback Score: 26 reviews
Leak down is more accurate.
__________________
IG/TikTok-ThatS14_Z06guy
EsChassisLove is offline   Reply With Quote
Old 08-18-2013, 02:31 PM   #27
EsChassisLove
Nissanaholic!
 
EsChassisLove's Avatar
 
Join Date: Jan 2011
Location: San Diego
Age: 34
Posts: 2,090
Trader Rating: (26)
EsChassisLove is an unknown quantity at this point
Feedback Score: 26 reviews
Quote:
Originally Posted by Itzgunzduh View Post
How would i know if its set up properly
PCV to manifold, and I suggest putting a catch between the two. Nissan PCVs are garage and will let oil in and pool in your manifold.

Then off the T on the driver side, rear goes to the black catch can, and the front goes to your intake pipe.

The PCV is for vacuum, but it closes under boost, that's when the intake pipe takes over and uses that to evacuate the pressure.
__________________
IG/TikTok-ThatS14_Z06guy
EsChassisLove is offline   Reply With Quote
Old 08-18-2013, 02:32 PM   #28
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by EsChassisLove View Post
PCV to manifold, and I suggest putting a catch between the two. Nissan PCVs are garage and will let oil in and pool in your manifold.

Then off the T on the driver side, rear goes to the black catch can, and the front goes to your intake pipe.

The PCV is for vacuum, but it closes under boost, that's when the intake pipe takes over and uses that to evacuate the pressure.
Im gnna post vid n u tell me if its connected right .
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:38 PM   #29
Itzgunzduh
 
Itzgunzduh's Avatar
 
Join Date: Aug 2013
Location: My house duhh
Age: 32
Posts: 36
Trader Rating: (0)
Itzgunzduh is an unknown quantity at this point
Feedback Score: 0 reviews
View My Video
Itzgunzduh is offline   Reply With Quote
Old 08-18-2013, 02:41 PM   #30
EsChassisLove
Nissanaholic!
 
EsChassisLove's Avatar
 
Join Date: Jan 2011
Location: San Diego
Age: 34
Posts: 2,090
Trader Rating: (26)
EsChassisLove is an unknown quantity at this point
Feedback Score: 26 reviews
I can't view it. Lol. Just trace the lines. Easy day.
__________________
IG/TikTok-ThatS14_Z06guy
EsChassisLove is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 01:20 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net