NY FS: Race Ready S13 Hatch Enduro Race Car. LI, NY

[gills]

**PENDING SALE**

Hey all,

This build is a little unorthodox for Zilvia, but nonetheless, it's an S-chassis that's built for the track (grip/road-course in this case). It's been endurance raced exclusively. If you're not familiar, google American Endurance Racing, World Racing League, ChumpCar, Lucky Dog Racing League, 24 Hours of LeMons, etc.

So time to unload my S13 240sx (KA24DE engine) enduro car that is basically race ready to focus on a new build. *Pics and price below*

This chassis actually hasn't raced much; 3 races to be exact with a couple of HPDE's in between. It's our second S13 as the first one was wrecked and we transferred the roll cage to this chassis (see google drive link below). We won overall in this car at the New Hampshire LeMons race in 10/2015 (first 240sx to win overall in Lemons). The car is very well tooled with spares and well setup.

Following that race we prepped the car to run in AER at Watkins Glen (4/2016) with a new garage paint job and some fancier bits. Unfortunately, the KA spun a rod bearing on practice day after 70+ hours of total track time. We managed to find a good KA on Craigslist a couple hours away, swapped important parts from the blown engine, threw it in and managed to finish the weekend with a full day of racing (8 hours) on Sunday.

That engine is still in the car. It's sweating a bit from the seals and needs a refresh (gaskets, seals; compression is good), but runs well. We may or may not refresh it and give it a once over prior to sale depending on what a potential buyer wants. Here's some laps from Watkins Glen on said engine:

https://youtu.be/iEVqN-xTtWk

With that said, the car is very well setup, super easy and predictable to drive and is basically ready to roll. Every single part has been touched and addressed if required. How it stacks up in ChumpCar now with the new rules I'm not sure, but there are spares to easily bring it to a level that you may want. Will be perfectly fine in WRL, AER, or Lucky Dog. Car is setup for taller drivers and will come with all required safety items to pass tech. This car has passed tech in ChumpCar, 24 HOL, and AER in its current configuration and dates are all good to go.

Here are some build pictures for this chassis:

https://drive.google.com/open?id=0B1...UpXdEdqZGpTLUE

ZERO RUST on this car. All rust spots were dealt with, which consisted of typical frame rail fix and a couple spots on passenger side floor.

List where I'll probably forget some stuff:

Safety
-1.75" OD x 0.095" Wall DOM roll cage with NASCAR door bars on both sides
-FIA Momo Daytona XL Halo Seat
-Scroth 6 Point harness
-4 Liter Multi-Flo Steel Mechanical AFFF Fire System
-Window Net
-SFI Roll Cage padding
-NRG quick release steering wheel hub

Suspension/Wheels
-Ground Control Coil Over Sleeves, 450 lbs/in front, 350 lbs/in rear
-Koni yellow struts/shocks. Front strut housings modifed for increased bump travel
-ebay 30mm front sway bar
-stock rear sway bar
-solid rear subframe mounts
-Properly depowered steering rack (removed hydraulic piston and greased)
-slotted strut towers (easily get -4* camber)
-high strength extended wheel studs
-muteki SR48 forged steel lug nuts
-5x114.3 hubs
-15x8 +20 offset Rota Grids. 4 with 225/45 RS3v2's used 10 hours, 4 with brand new 225/45 RS3v2's*

Brakes
-Z32 300zx TT front (30mm thick) and rear brakes (no ebrake)
-Z32 brake master cylinder
-Hawk DTC-60 front, HT-10 rear (decent life left)
-Stainless steel brake lines
-3" brake ducting to front brakes
-LED trailer brake lights

Powertrain
-KA24DE engine
-stock 5 speed transmission (1/2 Redline LTW shockproof, 1/2 Redline MT90)
-OEM viscous LSD with stock final drive (4.083)
-unknown LTW flywheel
-OEM Exedy Clutch
-Ishihara Johnson windage tray and crank scraper (not in current engine)
-ARP head studs (not in current engine)
-eBay intake
-Stock exhaust manifold mated to 3" exhaust
-eBay Aluminum radiator
-16" SPAL electric fan
-Power steering delete

Misc.
-Odyssey PC680 battery
-Prosport Gauges wired to LED alarm lights in front of driver (oil temp, oil pressure, water temp, voltage)
-Switch panel with quality switches and push button start
-Master battery cutoff switch with alternator protection (pegasusautoracing part # 4430)
-Modified fuel filler neck for fast fuel fill (can fit Hunsaker fill tube diameter)
-OEM glass windshield
-OEM rear hatch glass
-Heat shielding on underbody from driver's feet to ass.
-Wrapped exhaust from "downpipe" to mid-section
-Nissan Data Scan II license to connect to ECU to monitor vitals

Spares
-transmission
-differential (not LSD)
-driveshaft
-rear subframe
-front subrame
-depowered steering rack
-brake booster
-Z32 front caliper
-Z32 front caliper rebuild kits
-KYB GR2 shocks
-unknown OE style lowering springs (140 lbs/in, 195 lbs/in, measured)
-modified 09 WRX front springs (260 lbs/in, measured)
-long tube headers
-front hubs
-front wheel bearings
-ignition coils
-power transistors
-spark plug wires
-spark plugs
-distributors
-a bunch of front and rear suspension links
-fuel tank and fill tube
-OEM clutch kit (used, but good)
-(2) KA24DE exhaust camshafts
-ECU
-Intake manifold
-KA engine block (spun bearing one at Watkins)
-KA24DE cylinder head
-custom baffled extra capacity oil pan (6qts+)
-Extra Redline MT-90 transmission fluid

How it currently sits:









Some random pictures:

Dismantling of wrecked chassis to re-use cage:










6'4" driver roof to helmet clearance:


Cat hump mod:


Custom seat mounts:




Custom modified oil pan. Obviously don't/can't run AC:




Modified extended strut housings:



Asking $6000.

Car is located on Long Island, NY about 1.5 hours east of NYC. Will consider meeting for the right buyer.

I will also consider a la carting the package to an extent if that will make a sale go through.

Please text/call sixthreeonesixeightzeroninefouronesix for best communication if serious.

[240sx_sr20det]

Awesome car! I've seen it first hand at WGI.

[dr_]

this is a steal.

[TomShanK]

Originally Posted by dr_

this is a steal.

Just sitting here waiting for Zilvia to say "$6k for a KA 240, blah blah blah"

Really well prepared car, glws! What a steal

[TheRealSy90]

Throw some modified knuckles up front and a shorter final drive and this would make a great starter drift car lol.

[gills]

Thanks fellas. I added some more random pictures for the hell of it.

The fire system and cage might be overkill for drifting, but it would absolutely make a perfect starting point for a high powered drift monster.

[TheRealSy90]

Honestly I think the cage is probably perfect for someone interested in Pro-Am and nothing wrong with a proper fire suppression system!

[bisoo369]

this is the price you get when a responsible adult sells a 240sx lol. a fair one!

[Reece]

Way cooler than 90% of cars in this for sale section. Looks like a blast.

[gills]

deposit received...