Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Chat > Builds (and builds only)

Builds (and builds only) Got a build thread? It goes here, build threads anywhere else on the forum will be locked and never moved.


Reply
 
Thread Tools Display Modes
Old 08-07-2013, 10:56 PM   #1
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
Kouki KA-T Build Thread

***Please move to builds section, sorry for the inconvenience***

Well it has been a while since ive first purchased my 1997 240sx and I figured id post a semi proper build thread since my first post has made much more progress.

Well i picked this bad boy up in January of 2012 from a guy in Delaware for 4200 bucks. Stock SE, auto, non abs, 13X,XXX miles 2 owners ... pretty good condition... no rust. And the guy was planning to swap an s14 sr in it so that came home with me too. However upon inspection the SR head was missing all kinds of shit, and honestly wasnt wanting an SR anyway. So I ended up parting that out to help get my 5 speed swap and some coilovers and what i had left to start building a spare KA i had bought locally (ended up being total junk ). So with that said over many long nights, spending money left and right, and countless drunken stoopers heres where its at...

Build List

Engine and Drivetrain:
KA24DE All New Gaskets and Seals
Bottom end work all done in House at R & W Enterprises
-Block Hot Tanked, Baked, Decked, Sleeved, Bored and Honed blah blah blah
-Manley Rods
-Supertech 9:1 .020+ Pistons
-Clevite Main Bearings
-Clevite Rod Bearings
-ARP Rod Bolts
-ARP Main Studs
-ARP Head Studs
-Crank was micro-polished
-Fully Balanced Rotational Assembly
Head received a full rebuild and some S13 240/248 cams
Timing Chain
Water Pump
Oil Pump
Full 3” HKS Hi Power Exhaust
***Also fabing up a set of custom 3.5" blast pipes
Airesearch T3/T4 Hybrid turbo (TO4B compressor housing .60 AR
machined to fit TO4E 57 compressor wheel. Turbine is a T3 5 bolt .63 AR
machined to stage 3 with a ptrim turbine wheel re-profiled to fit a stage
three hole)
Oil feed lines
CX Racing T3/T4 Top Mount Manifold
CX Racing Down Pipe
38mm Tial Wastegate
SR 370cc Injectors
Precision 880cc Injectors
Top Mount Fuel Rail
Walbro 255 Fuel Pump
HKS SSQV Blow off Valve
Custom High Mount Intercooler
CX Racing Radiator
Dual Slim Fans
Z32 MAF
HKS Shroom Filter
NGK BKR7E Plugs
HKS Turbo Timer
Enthalpy Tuned ECU
5 Speed Trans
RB25DET XTD Lightweight Flywheel
RB25DET XTD Stage 3 6 Puck Sprung Clutch
Interior:
NRG Short Hub
NRG Quick Release
NRG 350mm Black Suede Red Stitch Wheel
Proper Bubble Shift Knob
Proper E-brake Knob
Glowshift 7 Series Gauges (Oil Pressure, A/F w/ wideband, and Boost)

Exterior:
Uras Type 4 Rep Front
Vertex Rep Sides
Vertex Rep Rear
9k Racing Dmax Rep Roof Spoiler
GP Sports Rep 3 Piece Trunk Spoiler
***Paint Coming Soon*** (A new twist on Hellrot Red ;P)
Morimoto Mini H1 Bixenon Projector Retroquick with Gattling Gun Shrouds in Blacked Out Headlight Housing

Suspension/Handling:
Function and Form Type 2 Coilovers
10k Swift Upgrade Springs for the Front
Godspeed Gen 2.5 Arm Package
Project Mu Locking Lugs
17x9+25 17x10.5+20 Mustang Wheels (Black Chrome)
17x8.5 +30 Cobra Wheels +30mm Spacers (Drift Spares)
15mm Spacers Front 10mm Spacers Rear

While waiting for some parts in the mail... i got parts in the mail!



So I started to order some parts here and there for the 5 Speed swap since the auto had to go... and plopped that in with the help of my buddy Jake Shoemaker and my buddy AK. Here's how she sat after all that...


Getting to work... (aka a random collection of events and images leading up to today)

Rods

Supertech Pistons

Poopy Fitment

Booty Hole

Interesting...

Interior Shot

Bought this stuff and then sold most of it other than some seals and gaskets lol

Blast Pipes (need to add 3.5" chrome slant tips this weekend)

"Clubloose Apparel" and my Autotimer

AK's Fully Built SR Zenki/Thee Garage

KDF Stuff

Stockpiling for shredding season

Morimoto Minis in place of stock projector (much better output imo)

Made some adjustments and got and alignment so she sits pretty...

Dope aristo from the FDR meet (SUPRLIFE)

Shoemakers S13 318rwhp SR


Spring Moves for some shredding with ^^^

Got my roof wing in the mail... so i casually put it on my dads corolla while picking it up from home...

Starting to test fit the kit...

Built motor home for final assembly...

Banishing the demon that put the car out of commission.... Guess that one day when smoke started pouring out of my front vents smelling like burning electrical will do that. Replaced every single harness in the thing.

Built Motor is in for first start and an idea of where im going...


More tomorrow if i have the time ... too tired.

Last edited by josh_schul; 04-09-2014 at 10:43 AM..
josh_schul is offline   Reply With Quote
Sponsored Links
Old 08-07-2013, 11:34 PM   #2
Mustache240
Zilvia Addict
 
Mustache240's Avatar
 
Join Date: Jan 2011
Location: Perris
Age: 32
Posts: 688
Trader Rating: (10)
Mustache240 is making a name for him/her selfMustache240 is making a name for him/her selfMustache240 is making a name for him/her self
Feedback Score: 10 reviews
Nice! Looking forward for updates on this thing
Mustache240 is offline   Reply With Quote
Old 08-08-2013, 07:17 PM   #3
d_nice
Post Whore!
 
d_nice's Avatar
 
Join Date: Aug 2010
Location: florida
Age: 43
Posts: 3,595
Trader Rating: (39)
d_nice is a well-known jackass
Feedback Score: 39 reviews
good parts and cant wait for more updates.
d_nice is offline   Reply With Quote
Old 08-08-2013, 07:33 PM   #4
240SilviaX
Leaky Injector
 
240SilviaX's Avatar
 
Join Date: May 2012
Location: HB / OC, CA
Age: 37
Posts: 120
Trader Rating: (2)
240SilviaX is an unknown quantity at this point
Feedback Score: 2 reviews
you sleeved an Iron block?? thought only aluminum ones came sleeved.
240SilviaX is offline   Reply With Quote
Old 08-08-2013, 07:59 PM   #5
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
Quote:
Originally Posted by 240SilviaX View Post
you sleeved an Iron block?? thought only aluminum ones came sleeved.
Sorry... i guess i should have elaborated... but one of the cylinders was a little iffy after the bore and hone so it was junk a block i had already started to spend money on or buy a new one and do it all again... so I had the trouble cylinder sleeved instead of starting again. R & W has made multiple 700+ blocks for KA24DEs and he insists its his favorite motor next to the 4g63s. Hope that makes sense..

dut in theory you could "sleeve" any block...
josh_schul is offline   Reply With Quote
Old 04-09-2014, 08:59 AM   #6
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
*double post*
josh_schul is offline   Reply With Quote
Old 04-09-2014, 09:10 AM   #7
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
Well we have been pretty much at a stand still for a bit. Hopefully selling off some extra bits i have laying around so i can start mocking up intercooler piping and mount up the turbo manifold and start getting her ready for boost. Also will start sanding for paint. Pics this weekend for sure. Got new pads and rotors i need to put on. As well as new struts to replace the blown ones from the craters in Pennsylvania's roads.

First Start (NA)
http://instagram.com/p/eicpkAqp1i/

Current shot

josh_schul is offline   Reply With Quote
Old 04-10-2014, 07:33 AM   #8
mewantkouki
Zilvia FREAK!
 
Join Date: Nov 2007
Location: Orlando, Fl
Age: 37
Posts: 1,249
Trader Rating: (36)
mewantkouki will become famous soon enoughmewantkouki will become famous soon enoughmewantkouki will become famous soon enough
Feedback Score: 36 reviews
What did it cost you to replace the "sleeves" in your ka? lmao
mewantkouki is offline   Reply With Quote
Old 04-10-2014, 02:44 PM   #9
GroundPerformance
Zilvia FREAK!
 
GroundPerformance's Avatar
 
Join Date: Oct 2008
Location: Socal
Posts: 1,479
Trader Rating: (44)
GroundPerformance is an unknown quantity at this point
Feedback Score: 44 reviews
I want a sleeved block myself.. Must have cost alot..
__________________

SoCal KA24DET/KA24ET Owners
<< Join the FB Group >>
GroundPerformance is offline   Reply With Quote
Old 04-17-2014, 08:11 AM   #10
kat7
 
Join Date: Apr 2014
Location: nj
Posts: 22
Trader Rating: (0)
kat7 is an unknown quantity at this point
Feedback Score: 0 reviews
A sleeved KA block??????????
kat7 is offline   Reply With Quote
Old 04-17-2014, 06:27 PM   #11
hamizle
Leaky Injector
 
hamizle's Avatar
 
Join Date: Apr 2012
Location: Centennial, CO
Age: 36
Posts: 98
Trader Rating: (1)
hamizle is an unknown quantity at this point
Feedback Score: 1 reviews
how about reading the thread? hes already answered why he sleeved the block..

"Sorry... i guess i should have elaborated... but one of the cylinders was a little iffy after the bore and hone so it was junk a block i had already started to spend money on or buy a new one and do it all again... so I had the trouble cylinder sleeved instead of starting again. R & W has made multiple 700+ blocks for KA24DEs and he insists its his favorite motor next to the 4g63s. Hope that makes sense..

dut in theory you could "sleeve" any block..."
hamizle is offline   Reply With Quote
Old 04-21-2014, 05:21 PM   #12
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
If you read, like ^^^^^ pointed out, you would have known the answer to this.

Anyways 550 cc injectors and some 5 ply elbows and reducers are being 2 day aired to my apt. So hopefully I can run my enthalpy tune for a bit... at least until I order my a gt30 and megasquirt around June or july.

Sent from my SAMSUNG-SGH-I537 using Tapatalk
josh_schul is offline   Reply With Quote
Old 06-08-2014, 06:31 AM   #13
iampsyah
 
Join Date: Feb 2014
Location: Hawaii
Posts: 35
Trader Rating: (1)
iampsyah is an unknown quantity at this point
Feedback Score: 1 reviews
Amazing!! I'm wanting to run a KA-T in my Zenki
iampsyah is offline   Reply With Quote
Old 06-08-2014, 08:00 AM   #14
Carl H
Leaky Injector
 
Join Date: Aug 2003
Location: Baltimore, Md
Posts: 88
Trader Rating: (3)
Carl H is an unknown quantity at this point
Feedback Score: 3 reviews
Send a message via AIM to Carl H
you're going to want at least 740s for a ka-t (or any turbo 4 cylinder) if you want to make decent power.
Watch the enthlapy tune, scott was good but this current dude blows...
Had to remap several of those 'pro tuned' ecus for customers just to get the car drivable.
__________________
Of all the things I've lost, I truly miss my mind the most.
Carl H is offline   Reply With Quote
Old 06-13-2014, 07:05 AM   #15
josh_schul
Zilvia Member
 
Join Date: Jun 2011
Location: Coatesville PA
Age: 33
Posts: 220
Trader Rating: (1)
josh_schul is an unknown quantity at this point
Feedback Score: 1 reviews
Quote:
Originally Posted by iampsyah View Post
Amazing!! I'm wanting to run a KA-T in my Zenki
Quote:
Originally Posted by Carl H View Post
you're going to want at least 740s for a ka-t (or any turbo 4 cylinder) if you want to make decent power.
Watch the enthlapy tune, scott was good but this current dude blows...
Had to remap several of those 'pro tuned' ecus for customers just to get the car drivable.
Thanks man ... I have done quite a bit of research before diving into the build. I got a set of precision 880cc top feeds fpr and rail that will be going in with a gt3071 once I get tired of the enthalpy tune and want real power. Also will be getting it dyno tuned by Steve at Psi Proformance when that time comes. Thanks though.
josh_schul is offline   Reply With Quote
Reply

Bookmarks

Tags
build, ka24det, kouki, s14, turbo


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 06:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net