SC Fully Built Sr20det Partout - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

dcraine · 05-16-2018, 03:15 PM

Well the time has come, I recently got a killer deal on a 2jzgte so time to part ways with all of my Sr stuff. This motor only has 2,000 miles on it! Absolutely nothing wrong with it, pulled great, broke in properly and will take whatever you throw at it. I have most of the receipts for the parts and original boxes, weights of forged stuff.. ext.
Someone come buy this to fund my 2j build!
Will travel up to two hours to meet someone as long as gas money is involved.

Built Sr20det w/ 5 speed trans.
Stock bore
8:5:1 Compression
Je Pistons
Manley Rods
Acl Race Bearings
Arp Headstuds/Hardware throughout
Tomei Headgasket
New Valve Seals and Valve Job
Isr Oversized oil pan
Isr Gasket Kit
Isr lightweight pulleys
Oem waterpump/Thermostat
New timing kit
New dipstick tube
Stock fuel rail 370cc
Stock mani w/ stock t25
Xtd Stage 3 Clutch and Lightweight Flywheel
Circuit Sports shorthrow shifter
Exedy Slave
Tf valve cover nuts
Ecu
Cody Ace bracket for cold AC!

[IMG]

[/IMG]
[IMG]

[/IMG]

Will Sell full setup/swap for $3500
Built Sr20det
Trasmission
Intercooler Kit
Radiator w/ Fans
Driveshaft
Wiring Specialties Pro Harness
Walbro 255

Or just Built Sr/Tranny for $3000

Also have a good amount of random parts.

Tomei PonCams 256/256 - Only 3,000 miles, Will include new timing chain gears aswell.
$150

Circuit Sport Rocker Arm Stoppers
$25

Oem Master Cylinder
$25

Oem Sr fuel rail with 370cc injectors
$50

[IMG]

[/IMG]
[IMG]

[/IMG]

Oem Sr20det Intake Manifold with new gaskets and iavc.
$150

Oem Sr20det water necks
$25

Oem Sr20det Iavc
$35

Oem Sr20det Maf's
$70

[IMG]

[/IMG]

Oem Sr20det flywheel and pressure plates
$50 for one set

[IMG]

[/IMG]

New Isis z32 Maf and New Pigtail
$75

4x Oem Coilpacks
$75

Oem sr20det fuel rail without injectors
$20

Sr20det e6 ecu, ive ran this ecu on both my red and blacktop and it worked perfect.
$100

[IMG]

[/IMG]

Oem sr20det stock rods and pistons, nothing wrong with them besides some surface rust. Would be good for a budget build. All rings still on them, Went stock bore forged.
$50

[IMG]

[/IMG]

Sr20det Head, bottom end spun a rod. Nothing wrong with the head it had the Tomei Pon Cams in it and will not come with them unless you buy both.
$200

[IMG]

[/IMG]

Spare Sr20 Transmission
$200

[IMG]

[/IMG]

Bare sr20det valve cover and gasket
$75

[IMG]

[/IMG]

Cx racing brand new top mount t3/t4 manifold for sr20det. Was reinforced heavily and pressure tested by Borla Performance.
$200

[IMG]

[/IMG]

New Garrett Gt2871r .86
$Pending

Sard Top Feed fuel rail
$sold

1000cc Injector Dynamics Injectors
$sold

Spare Cas
$75

S14 black glove box
$50

S14 black outer cluster trim piece
$20

Innovate Lc-2 Wideband with new O2 sensor
$sold

Samiata · 05-16-2018, 04:58 PM

interested in turbo lmk if other guy doesn't go through

roninwon · 05-16-2018, 05:15 PM

Coil packs, cas?

dcraine · 05-16-2018, 05:34 PM

Quote:

Originally Posted by roninwon

Coil packs, cas?

Yes sir, have a spare cas and i believe two sets of coil packs.

dcraine · 05-16-2018, 05:35 PM

Quote:

Originally Posted by Samiata

interested in turbo lmk if other guy doesn't go through

Alright man, Ill keep you updated should be going through tonight.

roninwon · 05-16-2018, 07:54 PM

How much shipped to 13603?

nisileighty · 05-16-2018, 07:55 PM

Are they s13 valve covers?

Edit: Nvm, pics just loaded. I’ll take one, text me at 206 566 9749. Thanks.

borka · 05-16-2018, 09:57 PM

PM'd about ID1000 and Innovate WB

boya1989 · 05-17-2018, 07:47 AM

I need that intake that goes off the turbo

dcraine · 05-17-2018, 08:02 AM

Quote:

Originally Posted by boya1989

I need that intake that goes off the turbo

Not parting that out yet man

djtoonjr · 05-17-2018, 08:04 AM

How much for Cody Aces , a/c bracket? U got all the hardware? u got all the A?C stuff too? compressor, lines off compressor?

Kviper52 · 05-17-2018, 08:09 AM

LC-2 Still availible?

dcraine · 05-17-2018, 08:18 AM

Quote:

Originally Posted by djtoonjr

How much for Cody Aces , a/c bracket? U got all the hardware? u got all the A?C stuff too? compressor, lines off compressor?

$50 for the Cody ace bracket and I do have an ac compressor attached I’d let the whole setup go for $150. It worked perfect on my car, but I’m keeping the ac lines as im going to have ac on my 2j build.

dcraine · 05-17-2018, 08:19 AM

Quote:

Originally Posted by Kviper52

LC-2 Still availible?

Yes sir I sure do

borka · 05-17-2018, 08:24 AM

Quote:

Originally Posted by dcraine

Yes sir I sure do

i want the ID1000 and LC2. i am still waiting for you to reply to my PM.

djtoonjr · 05-17-2018, 01:16 PM

Quote:

Originally Posted by dcraine

$50 for the Cody ace bracket and I do have an ac compressor attached I’d let the whole setup go for $150. It worked perfect on my car, but I’m keeping the ac lines as im going to have ac on my 2j build.

What compressor is on it? can u PM pics of it, to verify it'll clear my manifold based on hose position? thanks

nisileighty · 05-17-2018, 01:23 PM

Bump for great seller. Fast shipping.

joaquin714 · 05-17-2018, 02:03 PM

Thanks for the Cody ace bracket! Quick communication and prompt shipping

Bump

Keegster · 05-17-2018, 06:22 PM

Interested in compressor if its a dual cam s13, and coil pack harness

lewisfk · 05-17-2018, 07:12 PM

What's up with ecu. I.e. tune

dcraine · 05-17-2018, 07:58 PM

Quote:

Originally Posted by lewisfk

What's up with ecu. I.e. tune

Stock Ecu stock tune

dcraine · 05-20-2018, 05:53 PM

Bump it up let’s get this stuff sold!

05-16-2018, 03:15 PM	#1
dcraine Join Date: Dec 2016 Location: South Carolina Age: 29 Posts: 30 Trader Rating: (1) Feedback Score: 1 reviews	Fully Built Sr20det Partout :: New Parts Updated! Well the time has come, I recently got a killer deal on a 2jzgte so time to part ways with all of my Sr stuff. This motor only has 2,000 miles on it! Absolutely nothing wrong with it, pulled great, broke in properly and will take whatever you throw at it. I have most of the receipts for the parts and original boxes, weights of forged stuff.. ext. Someone come buy this to fund my 2j build! Will travel up to two hours to meet someone as long as gas money is involved. Built Sr20det w/ 5 speed trans. Stock bore 8:5:1 Compression Je Pistons Manley Rods Acl Race Bearings Arp Headstuds/Hardware throughout Tomei Headgasket New Valve Seals and Valve Job Isr Oversized oil pan Isr Gasket Kit Isr lightweight pulleys Oem waterpump/Thermostat New timing kit New dipstick tube Stock fuel rail 370cc Stock mani w/ stock t25 Xtd Stage 3 Clutch and Lightweight Flywheel Circuit Sports shorthrow shifter Exedy Slave Tf valve cover nuts Ecu Cody Ace bracket for cold AC! [IMG][/IMG] [IMG][/IMG] [IMG] [/IMG] [IMG] [/IMG] [IMG][/IMG] [IMG] [/IMG] Will Sell full setup/swap for $3500 Built Sr20det Trasmission Intercooler Kit Radiator w/ Fans Driveshaft Wiring Specialties Pro Harness Walbro 255 Or just Built Sr/Tranny for $3000 Also have a good amount of random parts. Tomei PonCams 256/256 - Only 3,000 miles, Will include new timing chain gears aswell. $150 Circuit Sport Rocker Arm Stoppers $25 Oem Master Cylinder $25 Oem Sr fuel rail with 370cc injectors $50 [IMG] [/IMG] [IMG][/IMG] Oem Sr20det Intake Manifold with new gaskets and iavc. $150 Oem Sr20det water necks $25 Oem Sr20det Iavc $35 Oem Sr20det Maf's $70 [IMG][/IMG] Oem Sr20det flywheel and pressure plates $50 for one set [IMG][/IMG] New Isis z32 Maf and New Pigtail $75 4x Oem Coilpacks $75 Oem sr20det fuel rail without injectors $20 Sr20det e6 ecu, ive ran this ecu on both my red and blacktop and it worked perfect. $100 [IMG][/IMG] Oem sr20det stock rods and pistons, nothing wrong with them besides some surface rust. Would be good for a budget build. All rings still on them, Went stock bore forged. $50 [IMG][/IMG] Sr20det Head, bottom end spun a rod. Nothing wrong with the head it had the Tomei Pon Cams in it and will not come with them unless you buy both. $200 [IMG][/IMG] Spare Sr20 Transmission $200 [IMG][/IMG] Bare sr20det valve cover and gasket $75 [IMG][/IMG] Cx racing brand new top mount t3/t4 manifold for sr20det. Was reinforced heavily and pressure tested by Borla Performance. $200 [IMG] [/IMG] New Garrett Gt2871r .86 $Pending Sard Top Feed fuel rail $sold 1000cc Injector Dynamics Injectors $sold Spare Cas $75 S14 black glove box $50 S14 black outer cluster trim piece $20 Innovate Lc-2 Wideband with new O2 sensor $sold Last edited by dcraine; 05-17-2018 at 03:20 PM.. Reason: Updated Parts

05-16-2018, 05:15 PM	#3
roninwon Zilvia Junkie Join Date: Sep 2008 Location: Nampa, ID Age: 37 Posts: 557 Trader Rating: (7) Feedback Score: 7 reviews	Coil packs, cas? __________________

05-16-2018, 07:54 PM	#6
roninwon Zilvia Junkie Join Date: Sep 2008 Location: Nampa, ID Age: 37 Posts: 557 Trader Rating: (7) Feedback Score: 7 reviews	How much shipped to 13603? __________________

05-17-2018, 08:04 AM	#11
djtoonjr Leaky Injector Join Date: Feb 2016 Location: Sacramento CA Age: 30 Posts: 113 Trader Rating: (2) Feedback Score: 2 reviews	A/c How much for Cody Aces , a/c bracket? U got all the hardware? u got all the A?C stuff too? compressor, lines off compressor?

05-17-2018, 08:09 AM	#12
Kviper52 Zilvia Member Join Date: Jul 2012 Location: Georgia Age: 32 Posts: 292 Trader Rating: (3) Feedback Score: 3 reviews	LC-2 Still availible? __________________ 1991 240sx Coupe-Drift Car 1995 240sx LN1-Show Car 1993 Skyline ECR33-Street Car 1997 240sx -Wife Car My Cars and Their story: http://zilvia.net/f/showthread.php?t=657376

05-16-2018, 04:58 PM	#2
Samiata Join Date: May 2018 Location: UT Posts: 2 Trader Rating: (0) Feedback Score: 0 reviews	interested in turbo lmk if other guy doesn't go through

05-16-2018, 07:55 PM	#7
nisileighty Zilvia FREAK! Join Date: Feb 2016 Location: Seattle, WA Posts: 1,218 Trader Rating: (4) Feedback Score: 4 reviews	Are they s13 valve covers? Edit: Nvm, pics just loaded. I’ll take one, text me at 206 566 9749. Thanks.

05-16-2018, 09:57 PM	#8
borka Join Date: Nov 2002 Posts: 7 Trader Rating: (0) Feedback Score: 0 reviews	PM'd about ID1000 and Innovate WB

05-17-2018, 07:47 AM	#9
boya1989 Leaky Injector Join Date: Oct 2011 Location: nc Age: 34 Posts: 53 Trader Rating: (0) Feedback Score: 0 reviews	I need that intake that goes off the turbo

05-17-2018, 01:23 PM	#17
nisileighty Zilvia FREAK! Join Date: Feb 2016 Location: Seattle, WA Posts: 1,218 Trader Rating: (4) Feedback Score: 4 reviews	Bump for great seller. Fast shipping.

05-17-2018, 02:03 PM	#18
joaquin714 Zilvia Member Join Date: Jul 2007 Location: California Posts: 192 Trader Rating: (1) Feedback Score: 1 reviews	Thanks for the Cody ace bracket! Quick communication and prompt shipping Bump

05-17-2018, 06:22 PM	#19
Keegster Zilvia Member Join Date: Jan 2017 Location: Charlotte Posts: 163 Trader Rating: (0) Feedback Score: 0 reviews	Interested in compressor if its a dual cam s13, and coil pack harness

05-17-2018, 07:12 PM	#20
lewisfk Zilvia FREAK! Join Date: May 2009 Location: North Austin, Texas Age: 43 Posts: 1,163 Trader Rating: (13) Feedback Score: 13 reviews	What's up with ecu. I.e. tune

05-20-2018, 05:53 PM	#22
dcraine Join Date: Dec 2016 Location: South Carolina Age: 29 Posts: 30 Trader Rating: (1) Feedback Score: 1 reviews	Bump it up let’s get this stuff sold!