Hey guys and gals!!
I'm bored and I know it is nothing special compared to some other builds on here but I'm going to post a build thread
1989 240SX coupe ~ Platinum Blue Pearl with Charcol bottom
Engine
-1991 Redtop SR20det - 72xxx kms
-300ZX fuel filter
-Megan racing turbo elbow
-Option Imports 3" Downpipe ( very difficult to deal with do not buy from them )
-Circut Sport Stainless RAS
-Greddy V-spec FMIC kit
-Greddy Type RS BOV ( Blue )
-Koyo rad
-Zirgo dual 12" e-fans
-Gladman cooling panel powder-coated Starlight blue
-Megan BMC Heat sheild
-Powder-coated Valve cover Starlight Blue ( Metallic blue )
-DOHC Power steering hooked up ( not a factory thing for the 89's to have the dohc stup for the sr so I guess it counts as a mod ? )
-Walbaro 255 LPH fuel pump
-Nismo FPR
-Apexi 13kg/cm2 rad cap
-Tomei Expreme manifold- recently replaced with a HKS manifold.
-Garrett GT2560R -4 (same as the S15 turbo, BB, but a 53mm inake instead of 49mm)
-7 layer S15 exhaust gasket
-Circuit Sports turbo lines
-Nismo Motor Mounts
-Apex Headgasket ( not installed )
-DOHC throttle cable
-New turbo/exhaust gaskets
-Buddyclub Spec III catback
-Circuit Sports Clear Cas cover
-Mushimoto rad shroud
-Circuit Sports Coolant Resivour
-Chrome dome nut's for Valve cover
-OEM washer's and grommets replaced ( 13 )
-Apexi Intake
-Nimso Oil Cap
-Circuit Sports Exhaust hangers
-Circuit Sports lightweight pulleys
Engine Management+Ignition
-Veilside RaceRom tuned ECU
-Splitfire Direct Ignition system
Suspension and Driveline
-Nismo Transmission mount
-B&M short shifter version 2
-BattleVersion RUCA's
-Megan Racing Street series coilovers
-Whiteline front and rear adjustable Sway bars
-Nismo Clutch line
-Deleted clutch diaphram
-Slotted Rear rotors
-RPS Street Series Clutch
-TODA 10.5lb Flywheel
-Z32 rear 5lug hubs
-BattleVersion Toe Rods
-Battleversion Tension Rods
-BattleVersion Traction rods
-S14 front 5lug hubs with S13 bearings pressed in
-JDM 300ZX TT Aluminum front 30mm Calipers powder-coated Stardust Black
-300ZX TT Aluminum rear calipers powder-coated Stardust Black
-300ZX ebrake system
-300ZX 15/16th BMC with third fitting pressed in
-Madpartz Z33 Track rotor to S-Chasis conversion bracket powder-coated gold
-350Z Track slotted and cross-drilled front rotor's
-300ZX slotted and cross-drilled rear rotor's
-Cusco Type MZ 2way diff with 5 bolt axle's
-Drive-shaft Shop (DSS) Steel 1 peice driveshaft ( 14 LBS )
-Relocated red top Optima to trunk with Taylor battery kit
-Agency Power front conversion lines
-PDM Rear conversion lines
-Russel Speed bleeders on all 4 calipers
Exterior
-Origin Crystal Tail lights, Converted to full LED by StatusLED
-Circuit Sports clear marker's with LED bulbs
-Cusco front license plate holder
-Rolled and Flared rear quater panels 30mm
-30mm rear widebody overfenders
-B-Magic rear bumper
-Vertx front bumper and sideskirts
-DMAX Dual 180sx Position and winker lights
-Zenki Silvia trunk lock
-
Rollers and tires
Front's: Varrstoen ES 2.2.1 18x9.5 +22 powder-coated White with Metallic Clear ( rainbow flake )
Rear's: Varrstoen ES 2.2.1 18x10.5 +0 powder-coated White with Metallic Clear ( rainbow flake )
Nismo Anti-theft valve caps
Muteki chrome Titanium lugs and lock lugs
Interior
-Nismo CF shift Knob
-MOMO Pit Stop ebrake handle
-Redline Shift and ebrake boots white with blue stripe leather
-MOMO 330mm steering wheel ( Monte Carlo )
-Silvia gauge cluster with white and blue LED back lighting and working HUD
-Pioneer CD-less deck
-JBL front and rear speakers
-Autometer dual gauge pod
-AEM EUGO Wideband
-AEM Tru-Boost Controller
-Blitz FATT
-Triple center vent gauge pod.
-Bride Stradia 2 with sparkle backs
-Bride rails
To be Installed
-HKS 264 IN/EX camshaft's
-Brian Crower Spring and Ti retainer
-HKS Exhuast Cam Gear
-Tomei Intake Cam Gear
-Tomei N2 Oil block
-Greddy Oil filter relocation block with hookup for oil cooler
-B&M oil cooler with -10 AN Hose and fittings.
-Defi White Racer series : Water temp, Oil Pressure, EGT guages
-Nismo extended studs
-Full Race topmount manifold, turbo elbow, Greddy Downpipe
Coming Soon
-GTX3071R .78 T3 twinscroll turbo
-AEM EMS with Map
-Tial MVR 44mm wastegate
-Nismo Powerbrace
-
-Tomei oil pan
-
-S13.4 Valve cover with AN fittings and custom breather tank.
-
-
Thing's I have powder-coated for the car
-upper rad bracket's
-valve cover
-front and rear brake caliper's
-wheel center cap's
-front hub dust cap's
-tri-gauge center vent holder
-cooling panel
-Battery tie down
-Shifter dust boot holder
-exhaust hanger holder for muffler
-ebrake cable brakets
if something chages I'll update it.