IN Race S13 Partout S14 ka Kaaz Megan vmount neukin manifold downpipe aluminum exhaust - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

neukin · 07-22-2009, 01:32 PM

Everything has about 1k miles on it... like NEW. Have to finish another car here and take care of business too so cant have two fully dont cars.

Chassis $2500 if you want the coilovers or other parts just add them
Neukin Tig Welded Roll cage chassis with ARP studs and 5lug new rotors and hwak pads 1.75 DOM tube .120 THE SAFEST out there
Custom cut gussets on drivers side tie cage into chassis for a ridged setup.
-Padding for impact safety and if you drive on street with no helmet
Muteki blk open wheel lugs and key
Walbro 255 intake fuel pump
no hood
Key for both doors, not used for start tho.. just switches for start
lock bolt in wheel is illegal for TTU race
classClear title and steetable
Odyssey PC680 battery (11 pounds!)
6 switch bank (used right now: fuel pump, fan 1, fan 2)
Two main switch near cluster (ign, and start)
Was a automatic so the chassis was setup and 5speed setup installed with correct pedals ect so you cant really tell but thought id toss that outthere.
THE LACK OF RUST IS GREAT, was not fixed.. it really has no major rust on chassis or frame rails.Has some small dents and such, i was never worried about looks since its a racecar. Would be easy to clean her up and put a kit or paint on.New slave and master for the clutch, new hardline and stainless flex line.

-Megan Racing 32-way "Track" Coilovers with front camber plates/pillow ball upper mounts all around. Re valved shocks for the stiffer springs
Front Coilovers bottom hole slotted for more camber (running 3 degrees of camber in front able to hit 5 degrees +)
$700

-Megan Front Roll Center Adjuster ball joints $100 (after you lower car these help flatten the lower control arms so Nissan designed suspension goes closer to intended geometry)
-Megan front steering S13 Rack Ends add more steering angle 55 SOLD
-Megan Engine / trans Mounts - much stiffer allowing the power to feed the wheels not a shaky engine. $95 SOLD
-Megan Tie Rod Ends 55 SOLD
-Megan Front Pillow Tension Rods 95
-Megan Rear Lower Toe Arms 65
-Megan Rear Lower Traction Rods 65
-Megan Rear Upper Control Arms 95

Russell stainless brake lines $70

Kaaz 2way LSD limited slip diff in pumpkin with blasted cover and black painted bolts $700

Steel one piece drive shaft $200 removes rotational weight and sends power to rear wheels for a clean snappy feel.

ready for s13 obd2 96 higher power S14 motor/ecu/trans has the ecu you can put Nistune on for a fully programable chip which id highly recommend to get this car to the next stage
Custom Wire harness from Nissan Wire Specialist and low miles clutch from center force Brand new alternator Neukin stainless Oil feed and stainless oil drain for turbo lube and cool system $800

Neukin vmount setup $750
-large Neukin intercooler for 650hp synapse flange for bov
-huge double pass radiator and mounting system
-Top feed filler neck
-silicone couplers and stainless T bolt clamps
-Stock hood lightened and louvered perfect for the intercooler core.
-Sparco hood pins/latch system from Italy
Dual 10" slim electric Fans

Neukin bottom mount manifold T3 44mm tial or 50mm synapse $600
Neukin 3" stainless downpipe with 02bung and flex section vband outlet
brake master cylinder shield for the safe side

Neukin power steering relocation keeps the pump cooler and better inlet for turbo s14 ka $100

Neukin Oil catch can with filter and baffle installed on front of valve cover. put a off center slant on the top of it to match valve cover contour $100

3" stainless exhaust system Neukin Mid Pipe Vband inlet and outlet with clamps $300

3" aluminum race exhaust downpipe back with custom mounts and hangers saves 20lbs and sounds good $400

NRG short hub, quick release wheel 2.5 and "Race" leather wheel w red stitch $220

One set of SportMax 17x8 with pretty much brand new fuzion zRi for daily or running to a event brand new (great in the rear for drifting) $500

One set of Motegi Traklite Rims 17x8 (only 15lbs each!) with R888 Toyos 2 with half tread 2 with 20% left. These are great track tires or use just in the front when drifting. $800
4) 10mm aluminum wheel spacers on the 4 corners for better wheel spacing.

S14 cluster and two of the needed three plugs $80

MAF N62 with pigtail $75 SOLD

Gorilla Unit 33 · 07-22-2009, 04:44 PM

Pics of Neukin power steering relocation? i cant see it on that pic

neukin · 07-23-2009, 01:21 PM

ummm here are a few at two angles the bottom one is the kit you would get.

spartanmisfit · 07-23-2009, 01:50 PM

that shit's nice man

bizump!!!!

nics fairlady · 07-23-2009, 08:31 PM

how much are you asking for the motor? and how much would shipping to 95834 be?

the.rise · 07-23-2009, 09:04 PM

would you do 70 shipped on the maf to 01923?

chris300zr · 07-24-2009, 09:39 AM

neukin intercooler kit require any cutting? looks like you cut the rad support out on that hatch? very interested but not looking to get rid of my support.

neukin · 07-24-2009, 10:06 AM

Ya the hood latch support needs cut, its well worth it. You can always get another one and put it back to stock later. Its a few spot rivits and you can get that section of meny junk s13ers. Id just do it.. for super sexy vmount action you must get nasty with a cut off wheel.

Just the motor, um not sure like $450, it has topfeed injectors and rail on it for easy tuning and injector choices. Rail has a gauge on it too. Runs great vac, no smoke adn it runs and starts like a F-ing champ. That way i can sell the trans for $400 with the newish centerforce clutch. Im sure shipping would be about $130 to massachusetts on pallet.

Few things sold and i didnt update list.

neukin · 07-30-2009, 01:06 PM

coilovers pending for sale fri/sat.... we will see.

still have the kaaz 2WAY!!! shoot a price 700 installed in there ready to rock with low miles and 3 fluid changes already with kaaz fluid. best condition used kaaz evvva

haggard240 · 08-06-2009, 08:03 PM

coils are amazing going to the track sunday to really test them out!! oh and they were UBER CLEAN!!

neukin · 08-10-2009, 05:00 PM

Thanks, coilovers sold. Need this KAAZ sold, someone pick this up its a deal!! 2 way super low use and fresh fluid. Installed in pumpkin already. 700 plus ship

240_fun · 08-10-2009, 10:44 PM

toe and traction arms to 08534?

aoiken3 · 08-11-2009, 02:49 AM

do u still have the odyssey battery? and if so, how much shipped to 93901?

pm me plz

slow92 · 08-11-2009, 06:26 AM

I know this is an old thread but do you still have the rucas??

g-via · 08-11-2009, 11:40 AM

this isn't an old thread, there has been discussion in it recently

How much for the steering wheel setup shipped?

neukin · 09-09-2009, 05:15 PM

Have this KAAZ out and ready to sell with final drive gear on it still all locktight'd n tq to spec ready to drop in....

(Can do Close to $700 shipped for most 48state guys west coast add $15) 2-WAY two way... very low use, two kaaz gear oil changes already three if you count the shit gear break in fluid it first had for break in. lmk need this gone!

07-22-2009, 01:32 PM	#1
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	Race S13 Partout S14 ka Kaaz Megan vmount neukin manifold downpipe aluminum exhaust Everything has about 1k miles on it... like NEW. Have to finish another car here and take care of business too so cant have two fully dont cars. Chassis $2500 if you want the coilovers or other parts just add them Neukin Tig Welded Roll cage chassis with ARP studs and 5lug new rotors and hwak pads 1.75 DOM tube .120 THE SAFEST out there Custom cut gussets on drivers side tie cage into chassis for a ridged setup. -Padding for impact safety and if you drive on street with no helmet Muteki blk open wheel lugs and key Walbro 255 intake fuel pump no hood Key for both doors, not used for start tho.. just switches for start lock bolt in wheel is illegal for TTU race classClear title and steetable Odyssey PC680 battery (11 pounds!) 6 switch bank (used right now: fuel pump, fan 1, fan 2) Two main switch near cluster (ign, and start) Was a automatic so the chassis was setup and 5speed setup installed with correct pedals ect so you cant really tell but thought id toss that outthere. THE LACK OF RUST IS GREAT, was not fixed.. it really has no major rust on chassis or frame rails.Has some small dents and such, i was never worried about looks since its a racecar. Would be easy to clean her up and put a kit or paint on.New slave and master for the clutch, new hardline and stainless flex line. -Megan Racing 32-way "Track" Coilovers with front camber plates/pillow ball upper mounts all around. Re valved shocks for the stiffer springs Front Coilovers bottom hole slotted for more camber (running 3 degrees of camber in front able to hit 5 degrees +) $700 -Megan Front Roll Center Adjuster ball joints $100 (after you lower car these help flatten the lower control arms so Nissan designed suspension goes closer to intended geometry) -Megan front steering S13 Rack Ends add more steering angle 55 SOLD -Megan Engine / trans Mounts - much stiffer allowing the power to feed the wheels not a shaky engine. $95 SOLD -Megan Tie Rod Ends 55 SOLD -Megan Front Pillow Tension Rods 95 -Megan Rear Lower Toe Arms 65 -Megan Rear Lower Traction Rods 65 -Megan Rear Upper Control Arms 95 Russell stainless brake lines $70 Kaaz 2way LSD limited slip diff in pumpkin with blasted cover and black painted bolts $700 Steel one piece drive shaft $200 removes rotational weight and sends power to rear wheels for a clean snappy feel. ready for s13 obd2 96 higher power S14 motor/ecu/trans has the ecu you can put Nistune on for a fully programable chip which id highly recommend to get this car to the next stage Custom Wire harness from Nissan Wire Specialist and low miles clutch from center force Brand new alternator Neukin stainless Oil feed and stainless oil drain for turbo lube and cool system $800 Neukin vmount setup $750 -large Neukin intercooler for 650hp synapse flange for bov -huge double pass radiator and mounting system -Top feed filler neck -silicone couplers and stainless T bolt clamps -Stock hood lightened and louvered perfect for the intercooler core. -Sparco hood pins/latch system from Italy Dual 10" slim electric Fans Neukin bottom mount manifold T3 44mm tial or 50mm synapse $600 Neukin 3" stainless downpipe with 02bung and flex section vband outlet brake master cylinder shield for the safe side Neukin power steering relocation keeps the pump cooler and better inlet for turbo s14 ka $100 Neukin Oil catch can with filter and baffle installed on front of valve cover. put a off center slant on the top of it to match valve cover contour $100 3" stainless exhaust system Neukin Mid Pipe Vband inlet and outlet with clamps $300 3" aluminum race exhaust downpipe back with custom mounts and hangers saves 20lbs and sounds good $400 NRG short hub, quick release wheel 2.5 and "Race" leather wheel w red stitch $220 One set of SportMax 17x8 with pretty much brand new fuzion zRi for daily or running to a event brand new (great in the rear for drifting) $500 One set of Motegi Traklite Rims 17x8 (only 15lbs each!) with R888 Toyos 2 with half tread 2 with 20% left. These are great track tires or use just in the front when drifting. $800 4) 10mm aluminum wheel spacers on the 4 corners for better wheel spacing. S14 cluster and two of the needed three plugs $80 MAF N62 with pigtail $75 SOLD __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com Last edited by neukin; 07-24-2009 at 10:07 AM.

07-22-2009, 04:44 PM	#2
Gorilla Unit 33 Zilvia Member Join Date: Oct 2006 Location: Philly Posts: 279 Trader Rating: (1)	Pics of Neukin power steering relocation? i cant see it on that pic __________________ gorillaunit33.wordpress.com

07-23-2009, 01:21 PM	#3
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	ummm here are a few at two angles the bottom one is the kit you would get. __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com

07-24-2009, 10:06 AM	#8
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	Ya the hood latch support needs cut, its well worth it. You can always get another one and put it back to stock later. Its a few spot rivits and you can get that section of meny junk s13ers. Id just do it.. for super sexy vmount action you must get nasty with a cut off wheel. Just the motor, um not sure like $450, it has topfeed injectors and rail on it for easy tuning and injector choices. Rail has a gauge on it too. Runs great vac, no smoke adn it runs and starts like a F-ing champ. That way i can sell the trans for $400 with the newish centerforce clutch. Im sure shipping would be about $130 to massachusetts on pallet. Few things sold and i didnt update list. __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com

07-30-2009, 01:06 PM	#9
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	coilovers pending for sale fri/sat.... we will see. still have the kaaz 2WAY!!! shoot a price 700 installed in there ready to rock with low miles and 3 fluid changes already with kaaz fluid. best condition used kaaz evvva __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com

Sponsored Links
Remove these by purchasing a Premium Membership with Zilvia.net!

07-23-2009, 01:50 PM	#4
spartanmisfit Zilvia Junkie Join Date: Jul 2008 Location: East Lansing, Michigan Age: 26 Posts: 371 Trader Rating: (1)	that shit's nice man bizump!!!!

07-23-2009, 08:31 PM	#5
nics fairlady Join Date: Jul 2009 Location: sacramento Age: 19 Posts: 2 Trader Rating: (0)	how much are you asking for the motor? and how much would shipping to 95834 be?

07-23-2009, 09:04 PM	#6
the.rise Join Date: Jun 2009 Location: Boston Age: 20 Posts: 29 Trader Rating: (1)	would you do 70 shipped on the maf to 01923?

07-24-2009, 09:39 AM	#7
chris300zr Zilvia Junkie Join Date: Dec 2005 Location: tejas Posts: 444 Trader Rating: (0)	neukin intercooler kit require any cutting? looks like you cut the rad support out on that hatch? very interested but not looking to get rid of my support.

08-06-2009, 08:03 PM	#10
haggard240 Join Date: Mar 2009 Location: massillon ohio Age: 21 Posts: 46 Trader Rating: (0)	coils are amazing going to the track sunday to really test them out!! oh and they were UBER CLEAN!! __________________

08-10-2009, 05:00 PM	#11
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	Thanks, coilovers sold. Need this KAAZ sold, someone pick this up its a deal!! 2 way super low use and fresh fluid. Installed in pumpkin already. 700 plus ship __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com

08-10-2009, 10:44 PM	#12
240_fun Join Date: Jan 2008 Location: Pennington Age: 19 Posts: 42 Trader Rating: (1)	toe and traction arms to 08534?

08-11-2009, 02:49 AM	#13
aoiken3 Zilvia Addict Join Date: Aug 2007 Location: monterey bay, ca Posts: 653 Trader Rating: (5)	do u still have the odyssey battery? and if so, how much shipped to 93901? pm me plz __________________ おれのシルビア大好きだよ！！！

08-11-2009, 06:26 AM	#14
slow92 Leaky Injector Join Date: Jun 2008 Location: SAVANNAH Posts: 58 Trader Rating: (0)	I know this is an old thread but do you still have the rucas?? __________________ S13 Coupe SR20 400whp

08-11-2009, 11:40 AM	#15
g-via Zilvia Addict Join Date: Jun 2007 Location: B.C., Canada Posts: 750 Trader Rating: (0)	this isn't an old thread, there has been discussion in it recently How much for the steering wheel setup shipped? __________________ "I'm a rage-aholic, I just can't live with rage-ahol!!!"

09-09-2009, 05:15 PM	#16
neukin Leaky Injector Join Date: Mar 2008 Location: Fort Wayne IN Posts: 134 Trader Rating: (1)	Have this KAAZ out and ready to sell with final drive gear on it still all locktight'd n tq to spec ready to drop in.... (Can do Close to $700 shipped for most 48state guys west coast add $15) 2-WAY two way... very low use, two kaaz gear oil changes already three if you count the shit gear break in fluid it first had for break in. lmk need this gone! __________________ Neukin Motor Development llc 399 River Bend CT Fort Wayne IN 46803 www.neukin.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode