s13 coupe silvia front doesn't line up - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

jeb1517 · 01-06-2009, 07:39 PM

I recently...acquired...an s13 that already had the silvia front end on it. The only gay part is that on the driver's side, the hood sits lower than the fender, maybe half an inch I would say right by the headlight (the difference gets less as you go towards the windshield obviously). I don't know if it's noticable to the average person but it annoys the F%*@ out of me.

I read about some installs and it doesn't seem like that difficult of a swap. Could there be a bracket or something missing? Should I take it apart and refit it? Or maybe its as simple as just re-fitting the hood? Any thoughts or suggestions would be appreciated. I'll try to get pics up soon.

*alzahakar* · 01-06-2009, 08:40 PM

Make sure the hood stops are there/adjusted correctly.

4x4le · 01-07-2009, 07:43 PM

^^yep, I removed my hood stoppers and put in hood pins, but they searve the same principal if they are properly adjustible.

Another thing you can do is remove the fender and bend the lip that bolts to the car up just a little and then test fit the fender again.

redsx13 · 01-09-2009, 02:02 PM

Quote:

Originally Posted by alzahakar

Make sure the hood stops are there/adjusted correctly.

+1, check you stops

jeb1517 · 01-21-2009, 05:28 PM

Sorry this took so long but anyways...haven't had a chance to check the hood stops but just wanted to post the pics up, i guess there's no reason for the pics anymore but since i took em i figured might as well post em. I'll post back after i get a chance to check the stops but chicago weather has been really gay lately n school is not helping either...thanks for the replies though

*jon_mr2* · 05-24-2009, 06:31 PM

if not the hood stops, check your hood hinge. the one 240 i am working on was rusted and the hood hinge started to seize and never really worked good. so, when i opened the hood, the hinge would bend at the bracket and cause the hinge to be warped... it eventually broke, lol. but now i got some new ones. hope you figure it out.

01-06-2009, 07:39 PM	#1
jeb1517 Join Date: Dec 2008 Location: Chicago Age: 25 Posts: 48 Trader Rating: (3)	s13 coupe silvia front doesn't line up I recently...acquired...an s13 that already had the silvia front end on it. The only gay part is that on the driver's side, the hood sits lower than the fender, maybe half an inch I would say right by the headlight (the difference gets less as you go towards the windshield obviously). I don't know if it's noticable to the average person but it annoys the F%*@ out of me. I read about some installs and it doesn't seem like that difficult of a swap. Could there be a bracket or something missing? Should I take it apart and refit it? Or maybe its as simple as just re-fitting the hood? Any thoughts or suggestions would be appreciated. I'll try to get pics up soon.

01-07-2009, 07:43 PM	#3
4x4le Zilvia Junkie Join Date: Nov 2008 Location: Manchester, Tn Posts: 479 Trader Rating: (0)	^^yep, I removed my hood stoppers and put in hood pins, but they searve the same principal if they are properly adjustible. Another thing you can do is remove the fender and bend the lip that bolts to the car up just a little and then test fit the fender again. __________________ NEW/CHEAP s13/14sr CAS Authorized NIStune Dealer

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Sponsored Links
Remove these by purchasing a Premium Membership with Zilvia.net!

01-06-2009, 08:40 PM	#2
alzahakar Still Useless Join Date: Aug 2008 Location: Las Vegas Age: 27 Posts: 186 Trader Rating: (3)	Make sure the hood stops are there/adjusted correctly.

01-21-2009, 05:28 PM	#5
jeb1517 Join Date: Dec 2008 Location: Chicago Age: 25 Posts: 48 Trader Rating: (3)	Sorry this took so long but anyways...haven't had a chance to check the hood stops but just wanted to post the pics up, i guess there's no reason for the pics anymore but since i took em i figured might as well post em. I'll post back after i get a chance to check the stops but chicago weather has been really gay lately n school is not helping either...thanks for the replies though

05-24-2009, 06:31 PM	#6
jon_mr2 Premium Member Join Date: Sep 2005 Location: hawaii Age: 22 Posts: 186 Trader Rating: (3)	if not the hood stops, check your hood hinge. the one 240 i am working on was rusted and the hood hinge started to seize and never really worked good. so, when i opened the hood, the hinge would bend at the bracket and cause the hinge to be warped... it eventually broke, lol. but now i got some new ones. hope you figure it out.